Toolex 596702, Руководство пользователя, Страница: 1 / 9

5
6
7
8
01A. Piston
02A. Blade Part
03A. Cutting Blade
1
1 ) Work area safety
a) Keep work area clean and well lit. Cluttered and dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools create sparks which may ignite the dust
or fumes.
c)
Keep children and bystanders away while operating a power tool.
Distractions can
cause you to lose control.
2) Electrical safety
SAFETY INSTRUCTIONS
PLEASE READ & UNDERSTAND THESE INSTRUCTIONS!
STORE THESE INSTRUCTIONS IN A SAFE PLACE!
GENERAL SAFETY RULES.
WARNING!
FAILURE TO FOLLOW ALL INSTRUCTIONS LISTED BELOW & OVERLEAF MAY RESULT IN
ELECTRIC SHOCK, FIRE &/OR SERIOUS INJURY. THE TERM 'POWER TOOL' IN ALL WARNINGS
LISTED HERE REFERS TO YOUR MAINS OPERATED [CORDED] POWER TOOL OR
BATTERY-OPERATED (CORDLESS) POWER TOOL.
TOOLEX INDUSTRIAL 596702
4.0MM METAL CUTTING NIBBLER.
596702
4.0MM METAL CUTTING NIBBLER
Read through carefully and understand these instructions before use
2
Picture 3
1. Gear Housing
2. Orientation Pin
3. Piston
4. Cutting Blade
5. Orientation Hole
6. Piston Sleeve
7. Gasket
8. Blade Part
9. Up-Blade Block
10. Down-Blade Block
11-12. 5x14 Inner Hexanglar Screw
13. Screw Sleeve
04A. Up-Blade Block
05A. Down-Blade Block
3
4
INSTRUCTIONS
Electric Metal Cutting Nibbler
Thanks for purchasing our heavy duty metal cutting nibbler. This machine is for cutting
most forms of metal sheeting, nonferrous metal sheet & other similar sheeting with a
thickness of 4.0mm or less. Please read & understand these instructions & keep in a
safe place.
WARNING: Please read these instruction before you use this tool!
It's possible you can be injured if you don't read & understand all instructions below.
Remove the plug from the power supply before any maintenance is carried out.
Check the voltage on the name plate is the same as your power supply.
Make sure the switch is in the off position before connecting to mains power.
Do not exceed the maximum cut capacity of this tool.
Only use this tool in applications as described in the instructions.
Make sure the unit is at full speed before you start cutting the material.
It is recommended to use some cut lubrication on some materials.
Children should not use this machine.
Note:
1. Please make sure that all screws are tight on the machine before you operate the
nibbler & always have the auxiliary handle fitted to the machine.
2. Children are advised not to use this machine due to the heavy weight & to avoid any
possible accidents.
3
.
The material being cut should be clamped to a worktable. Push the switch lever
forward & the nibbler blade will start to run, you can then start to cut the material,
make sure the nibbler is kept at a level angle to the work-piece for the best cutting
performance.
4. Make sure the nibbler is only rested on the cutting sheet when you are cutting the
material. Otherwise the blade & holder may be damaged.
FEATURES:
Unique design & extremely durable machine.
Excellent cutting speed & performance.
Cuts without sparking & leaves a burr free cut edge.
Nibbler can be spun a full 360 Degree while cutting the material.
Accomplishes a wide range of cutting shapes.
Cutting Blade & Guide are easily replaced to offer the best cutting performance.
1. Fixed Handle Arm.
2. Gear Housing
3. Switch
4. Auxiliary Handle
5. Cutting Blade Guide
6. Screw Sleeve
Cutting Capacity:
Sheet Steel & Iron Plate:
4.0
mm
Stainless Steel: ≤2.5mm
Other materials as aluminium copper zincalume: 4.0mm
Specifications:
Machine Length: 298mm
Cutter Head Height: 228mm
Nibbler weight: 4.0KG
Motor: 625Watt
Power Frequency: 50Hz
Cutting Blade Speed: 1000rpm
Content:
1. Heavy Duty Electric Sheet Cutter
2. Inner Hexangular Wrench
3. Screw Sleeve Wrench
4. Fixed Handle
5. Auxiliary Handle
6. Instruction Manual
7. Plastic Box
1pc
1pc
1pc
1pc
1pc
1pc
1pc
Picture 4
Replacement Instructions(Refer picture 3 & 4):
Replacement of dowm-blade block: Loosen two inner hexangular screws(12)
slowly with hex wrech(5mm) and replace with repaired down-blade block or
new down-blade block(10), then tighten two screw(12) .
Replacement of cuttin blade: Loosen two inner hexangular screws(11) slowly
with hex wrench(5mm) and take down upblade block(9), then release screw
sleeve with screw sleeve wrench and pull piston sleeve(6), release old cutting
blade(4) on piston sleeve and replace with repaired cutting blade or new
cutting blade, then reinstall to tighten any screws.
N3570
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do notuse any
adapter plugs with earthed (grounded) power tools. Unmodified plugs andmatching outlets will
reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,ranges and
refrigerators.
There is an increased risk of electric shock if your body isearthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool willincrease
the risk of electric shock.
d)
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging thepower
tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged orentangled cords
increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for outdooruse. Use
of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces the risk of electric shock.
3)
Personal safety
a) Stay alert, watch what you are doing and use common sense when operating apower tool.
Do not use a power tool while you are tired or under the influence ofdrugs, alcohol or
medication.
A moment of inattention while operating power
tools
mayresult in serious personal
injury.
b) Use personal protective equipment. Always wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions
will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to
power source and/or battery pack, picking up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or akey
left attached to a rotating part of the power tool may result in personal injury.
e)
Do not overreach. Keep proper footing and balance at all times.
This enables bettercontrol
of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing andgloves
away from moving parts. Loose clothes, jewellery or long hair can be caught inmoving parts.
g) If devices are provided for the connection of dust extraction and collection acilities, ensure
these are connected and properly used. Use of dust collection can reduce dust-related hazards.
4) Power tool use and care
a)
Do not force the power tool. Use the correct power tool for your application.
Thecorrect
power tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power tool
that cannot be controlled with the switch is dangerous and must be repaired.
d) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tools
operation. If damaged, have the power tool repaired before use. Many accidents are
caused by poorly maintained power
tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are easier to control.
5)
Service
a) Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
6)
Additional Information.
a)
Wear ear protectors.
Exposure to noise can cause hearing loss.
b) Always wear eye protection.
c) If the supply cord is damaged, it must be replaced by an authorized service agent
in order to avoid a hazard.
d) It is recommended that a residual current device of 30mA sensitivity or less is
used in the power supply system that this tool is to be plugged in to.
c) Disconnect the plug from the power source and/or the battery pack from the
power tool before making any adjustments, changing accessories, or storing power
tools.
Such preventive safety measures reduce the risk of starting the power tool accidentally.
g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking
into account the working conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous situation.