background image

 

 

 

In  Tube  mode,  the  supply  voltage  is  rectified  by  an  EZ81  (like  in  most  vintage 
amplifiers). This rectifier mode offers a slightly compressed tone. 

 

In  S.S.  (Solid  State)  mode,  the  supply  voltage  is  rectified  by  silicium  diodes  (like  most 
modern  amplifiers).  This  rectifier  mode  offers  a  stiffer,  direct  tone.  Your  amplifier  will 
also have more headroom, the range of clean tones becomes larger. 

 
 

The rectifier mode is selected thanks to the Power 

[1]

 switch: 

 

In the middle position, your amplifier is Off : the amplifier is unpowered 

 

In the upper position, your amplifier is powered and is in Tube mode 

 

In the lower position, your amplifier is powered and is in S.S. mode 
 

 
To  swap  from  one  rectifier  mode  to  another,  follow  the  ‘rectifier  mode  selection’  procedure 
below: 

1.

 

Put the amplifier in Standby : put the Standby 

[3] 

switch in the middle position 

2.

 

Wait for 30 seconds 

3.

 

Turn the amplifier Off : flip the Power 

[1] 

switch to the middle position 

4.

 

Select the desired rectifier mode (Tube or S.S.) 

5.

 

Wait for a few minutes to let the tubes heat-up 

6.

 

Select  the  Stage  or  Home mode  depending  on  the  desired  output  level  (see  next 
chapter). 

 

4.4. Output power selection 

 

The 

Crunch Machine

 allows you to select the maximum output level in order to take advantage 

of its tone in any situation: 
 

 

In  Stage  mode,  your  amplifier  has  its  full  18  watts  power  range.  This  power  level  is 
sufficient to play on small to medium-sized stages. 

 

In Home mode, the maximum output power is  approximately 4 watts. This power level 
allows  you  to  play  at  home  while  ‘pushing’  the  power  tubes  and  using  all  the  settings 

offered by your 

Crunch Machine

 
The selection of the output power level is done thanks to the Standby 

[2]

 switch: 

 

In  the  middle  position,  your  amplifier  is  on  Standby :  only  the  tubes  heating  system  is 
active 

 

In the upper position, your amplifier is in Stage mode 

 

In the lower position, your amplifier is in Home mode 

 
Whether in Stage or in  Home mode, your amplifier is operational : you are ready to play ! 
 

Содержание Crunch Machine















Отзывы: