Tolomatic • URL: http://www.tolomatic.com • Email: [email protected] • Fax: (763) 478-8080 • Toll Free: 1-800-328-2174
Parts Sheet #3600-4011_18_BCS10ps
Parts Sheet #3600-4011_18_BCS10ps
BCS10/MCS10
Reverse Parallel Mounting – 5
BCS10
MCS10
1:1 RATIO
2:1 RATIO
1:1 RATIO
2:1 RATIO
ITEM PART NO.
DESCRIPTION
MRV21,22,23,24
MRS231,232,MRB21
MRB31,32
MRS341,342,343
MRV21,22,23,24
MRS231,232,MRB21
MRB31,32
MRS341,342,343
MRV21,22,23,24
MRS231,232,MRB21
MRB31,32
MRS341,342,343
MRV21,22,23,24
MRS231,232,MRB21
MRB31,32
MRS341,342,343
1. 3420-1640 SHCS, M5 X 0.8, 50 MM LONG, LOW HEAD, SST 1 1
1 1
1 1
1 1
3420-1639 SHCS, M5 X 0.8, 55 MM LONG, LOW HEAD, SST
1 1
1 1
1 1
1 1
2. 0601-1618 COVER, BCS10/B3S10-23 FRAME
1 1
1 1
1 1
1 1
0602-1618 COVER, BCS10/B3S10-34 FRAME
1 1
1 1
1 1
1 1
3. 0510-1109 BEARING, BALL, RADIAL, Ø.250
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
4. 0510-1112 TIMING BELT, 11.00-1/5-3/8
1 1 1 1
1 1 1 1
0510-1113 TIMING BELT, 13.00-1/5-3/8
1 1 1 1
1 1 1 1
5. 0520-1067 CLAMP COLLAR, Ø.688
1
1
1
1
1
1
1
1
6. 0515-1191 PULLEY, 18 TEETH, .38 WIDTH
1 1 1 1
1 1 1 1
0510-1110 PULLEY, 36 TEETH, .38 WIDTH
1 1 1 1
1 1 1 1
7.
3420-1255 PULLEY, 18 TEETH, .38 WIDTH
1
1
1
1
1
1
1
1
0515-1191 PULLEY, 18 TEETH, .38 WIDTH
1
1
1
1
0515-1192 PULLEY, 18 TEETH, .38 WIDTH
1
1
1
1
8. 0510-1111 TRANTORQ, Ø.250
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
9. 0510-1111 TRANTORQ, Ø.250
1
1
1
1
0515-1181 TRANTORQ, Ø.375
1
1
1
1
10. 3410-1229 BHCS, TORX, 10-24, 0.50, BLK
4 4 4 4 4 4 4 4
3420-1644 SHCS, M5 X 0.8, 12 MM LONG, LOW HEAD
4 4 4 4 4 4 4 4
11. 0601-1053 PLATE, MOTOR, 23 FRAME
1 1
1 1
1 1
1 1
0602-1057 PLATE, MOTOR, 34 FRAME
1 1
1 1
1 1
1 1
12. 0601-1608 HOUSING, BCS10/B3S10-23 FRAME
1 1
1 1
1 1
1 1
0602-1608 HOUSING, BCS10/B3S10-34 FRAME
1 1
1 1
1 1
1 1
13. 0601-1625 SCREW, #6 X .25, SELF-TAPPING, SST
8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8
14. 0601-1602 END CAP
2 2
2 2
2 2
2 2
0602-1602 END CAP
2 2
2 2
2 2
2 2
15. 2212-1098 SHCS, M5 X 0.8, 20 MM LONG, SST
4
4
4
4
2212-1099 SHCS, M5 X 0.8, 25 MM LONG, SST
4
4 4 4
4 4 4
4 4 4
4 4
REVERSE PARALLEL DISASSEMBLY INSTRUCTIONS
1. Remove End Cap’s (#14). Release tension on belt by breaking loose the
motor screws (#15).
2. Remove RP Cover (#2).
3. Remove both drive pulley (#7) and driven pulley (#6) from their respective
shafts. The belt (#4) will come off with the pulley’s.
4. Remove motor screws (#15) from the motor plate (#11), to remove the motor
from the RP Housing.
5. Remove the RP Housing (#12) from the head by removing screws (#10).
REVERSE PARALLEL ASSEMBLY INSTRUCTIONS
*Apply Loctite #242 to all screws upon installation
1. Install RP Housing (#12) to the head with cap screws (#10). Do not fully tight-
en the screws at this time and verify that the RP Housing can move with
respect to the head.
2. Temporarily install the cover (#2) with bearing (#3) onto the RP Housing posi-
tioning the bearing over the leadscrew shaft. Hold the cover in place while
tightening all of the screws (#10) that hold the RP Housing to the head.
3. Remove the cover (#2) and finish tightening all screws attaching the RP
Housing to the head.
4. Install the motor to the RP Housing with screws (#15). Do not tighten the
screws at this time.
5. Locate the belt (#4) over the pulleys and slide the drive (#7) and driven (#6)
pulleys over their respective shafts. Tighten each pulley to it’s shaft with
either trantorque or collar clamp. If trantorque, utilize torque wrench to apply
appropriate torque. 1/2" hex on trantorque apply 75 in-lbs. 5/8" hex on tran-
torque apply 100 in-lbs.
6. Verify that there is clearance between the inside of the RP Housing and each
pulley. Verify that the pulleys are aligned to each other.
7. Position the cover (#2) in mating slot of the RP Housing and install the SHCS
(#1) to hold in place. Take care not to overtighten. If the cover is deflected it
can interfere with the leadscrew.
8. Tension the belt by pulling the motor away from the drive shaft with appropri-
ate force from chart below. Tighten the motor screws while this force is
applied to the motor.
Motor Frame
Tension Force
MRB23, MRS17/23 10 lbs
MRV23, MRS34
20 lbs
MRV34, MRB34
30 lbs
9. Install both end caps (#14) with the screws (#13) to finalize assembly.
10
15
8
6
3
4
2
1
5 7
9
11
14
12
13
