Tohnichi DOTE100N4-G Скачать руководство пользователя

Страница: 7 / 28

IGIT
AL T

ORQUE WRENCH TES

TER
D

TE4-G

External View

Display

Torque Display area indicates the torque value. Values are displayed in blue when an OK/

NG judgment result is OK, in red when it is LO/HI, and in white when no OK/NG Judg

ment is made.

Counter/Upper-limit

Value display

Display a serial number or an upper-limit value.

Upper-/Lower-limit

value Selection/Lower

-limit value display

Displays an upper-/lower-limit value selection status for OK/NG Judgment or

a lower-limit value.

▼

Mark display

RUN Lights up when RUN mode (Continuous display) is selected.
PEAK Lights up when PEAK mode (Maximum value display) is selected.
M.R Lights up when Auto memory/Reset is not set in the PEAK mode.

Lights up in the RUN mode.

A.R Lights up when Auto memory/Reset is set in the PEAK mode.

Unit

▼

appears on the unit (lbf·in, lbf·ft, cN·m, N·m, kgf·cm, kgf·m) selected.

Count forward Key

Moves the counter forward by one to read out measured data

Count backward Key

Moves the counter backward by one to read out measured data

Clear Key

In the PEAK mode, the peak value is reset. Or, the stored data is cleared.

In the RUN mode, auto zero adjustment is performed.

Statistic processing Key

This is a key for selecting the number of samples, maximum value, minimum value or

mean value.

Mode Key

This is a key for selecting the RUN mode or PEAK mode.

The upper-/lower-limit value selection screen is displayed by holding down the key for

2 seconds or longer.

Memory/Reset button

Stores the measured data (measured torque, measurement date and time) and

moves the counter forward by one after OK/NG Judgment of the measured data.

4-1. Display and Operation Keys

Torque Display

Clear key

Statistical processing key

Mode key

Counter/Upper-limit Value Display

Upper-/Lower-limit value

Selection/Lower-limit value display

▼ Mark display

Count forward key

Count backward key

Memory/Reset button

Содержание DOTE100N4-G





























Результаты поиска

Содержание DOTE100N4-G

Отзывы:

Похожие инструкции для DOTE100N4-G

Бренды по названию

Популярные бренды

Tohnichi DOTE100N4-G, Руководство по эксплуатации

Результаты поиска

Содержание DOTE100N4-G

Отзывы:

Похожие инструкции для DOTE100N4-G

Бренды по названию

Популярные бренды