manualshive.com logo in svg

TOHATSU MD 25B2 JET, Руководство пользователя

Поделиться
Скачать
TOHATSU MD 25B2 JET Скачать руководство пользователя страница 4

3

GENERAL INFORMATION

Before Operating Your Outboard

Read this manual carefully. Learn the difference in handling characteristics between a jet drive 
boat and a propeller driven boat. If you have any questions, contact your dealer.

STEERING AT LOW SPEEDS

Unlike propeller driven boats, the jet drive boat tends to lose steering control as less water is drawn 
in and expelled. Increase speed slightly to regain steering.

MANEUVERABILITY

The jet drive is highly maneuverable at higher speeds, more so, than propeller driven boats. Use 
caution when turning to prevent spin - outs.

IN NEUTRAL

The impeller will continue to rotate while the engine is in neutral. Although the approximate 
balancing of forward and reverse thrust will minimize boat movement, the boat may tend to move 
slowly forward or backward. This is normal for a direct - drive jet driven boat. The operator should 
be aware of this and use caution whenever the engine is running. 
Safety and operating information that is practiced, along with using good common sense, can 
help prevent personal injury and product damage. 
This manual as well as safety labels posted on the outboard use the following safety alerts1. to 
draw your attention to special safety instructions that should be followed.

DANGER

Indicates a hazardous situation which, if not avoided, will result in death or 
serious injury.

WARNING

Indicates a hazardous situation which, if not avoided, could result in death or 
serious injury.

2

MD25-35Jet_Owners_Sup_120216.indd   2

12/02/17   19:51

Содержание MD 25B2 JET





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды