manualshive.com logo in svg

TOHATSU MD 25B2 JET, Руководство пользователя

Поделиться
Скачать
TOHATSU MD 25B2 JET Скачать руководство пользователя страница 20

18

19

Corrosion Control Anode

An  anode  helps  protect  the  outboard  against  galvanic  corrosion  by  sacrificing  its  metal  to  be 
slowly corroded instead of the outboard metals.
An anode is located on the water intake housing. An anode requires periodic inspection, especially 
in  salt  water  which  will  accelerate  the  erosion. To  maintain  this  corrosion  protection,  always 
replace the anode before it is completely eroded. Never paint or apply a protective coating on the 
anode as this will reduce effectiveness of the anode.

a - Water intake housing anode

Lubricating the Driveshaft Bearing

Lubricate the driveshaft bearing before each use.

Description

Where to used

Part No.

Grease

Drive shaft bearing

3HT-72309-0

Grease Gun

Drive shaft bearing

3HT-65324-0

 IMPORTANT 

 :  

It is important not to use a general all purpose grease for this bearing. 
The  lubricant  recommended  is  a  water  resistant  grease  of  the  proper 
consistency for this application. If a substitute is used, be sure that it is 
water resistant and of the same consistency.

a

M25 Jet Drive

MD25-35Jet_Owners_Sup_120216.indd   18

12/02/17   19:51

Содержание MD 25B2 JET





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды