manualshive.com logo in svg

TOHATSU MD 25B2 JET, Руководство пользователя

Поделиться
Скачать
TOHATSU MD 25B2 JET Скачать руководство пользователя страница 15

12

13

Worn/Dull Impeller

The intake of gravel through the pump can round off and wear the leading edges of the impeller. 
Some conditions that could be experienced from a worn/dull impeller are as follows:
• Noticeable performance loss, especially on acceleration
• Difficulty getting the boat on plane
• An increase in engine RPM at wide open throttle

 IMPORTANT 

 :  

Do not sharpen or alter the top side lifting angle. Check the impeller 
blades occasionally for damage. Use a flat file to resharpen the leading 
edges. Sharpen to a 0.8 mm (1/32 in.) radius by removing material from 
bottom side only.

Steering Pull Adjustment

The  steering  on  some  boats  will  have  the  tendency  to  pull 
towards starboard. This pulling condition can be corrected by 
using a pliers and bending the ends of the exhaust fins 1/16 in. 
(1.5mm) toward the starboard side of the outboard.

Impeller Clearance Adjustment

The impeller should be adjusted so there is approximately 0.8 mm (0.031 in.) clearance between 
the impeller edge and liner. Operating the jet drive in waters that contain sand and gravel can 
cause wear to the impeller blades, and the clearance will start to exceed 0.8 mm (0.031 in.).

a - Exhaust fin

b

a

a - Leading edge 
b - Top side lifting angle

M25 Jet Drive

MD25-35Jet_Owners_Sup_120216.indd   13

12/02/17   19:51

Содержание MD 25B2 JET





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды