background image

2

1. SAFETy PRECAUTIONS

•  Before installation or use, be sure to carefully read all the instructions in this section for correct and safe 

operation.

•  Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or 

cautions regarding safety.

•  After reading, keep this manual handy for future reference.

Safety Symbol and message Conventions 

Safety symbols and messages described below are used in this manual to prevent bodily injury and property 

damage  which  could  result  from  mishandling.  Before  operating  your  product,  read  this  manual  first  and 

understand the safety symbols and messages so you are thoroughly aware of the potential safety hazards. 

Indicates a potentially hazardous situation which, if mishandled, could 

result in death or serious personal injury.

Indicates a potentially hazardous situation which, if mishandled, could 

result in moderate or minor personal injury, and/or property damage.

WARNING
CAUTION

When Installing the Unit

•  Refer all installation work to the dealer from whom 

the  speaker  was  purchased.  Installation  for  flying 

requires  extensive  technical  knowledge  and 

experience. The speaker may fall off if incorrectly 

installed, resulting in possible personal injury.

•  Install the unit only in a location that can structurally 

support  the  weight  of  the  unit  and  the  mounting 

bracket. Doing otherwise may result in the unit 

falling  down  and  causing  personal  injury  and/or 

property damage.

•  Flying Precautions (SR-F09 only)

  Be sure to follow the instructions below. Otherwise, 

the suspension wires or belts may be off or snap 

and  the  speaker  may  fall  off,  causing  personal 

injury.

·  Check to confirm that the suspension wires and 

belts are strong enough to withstand the speaker 

load.

·  The connectors of the suspension wires and belts 

must be securely linked with those of the speaker.

·  All  parts  and  components  (such  as  enclosures, 

metal pieces, and screws) must be free from any 

deformation, crack, and corrosion. 

·  Be sure to use screws supplied with the optional 

flying hardware when installing the speaker using 

such hardware. 

When Installing the Unit

•  Install the unit only in stable locations, and make 

appropriate arrangements to prevent it from falling 

down  or  rolling  cross  the  floor.  If  it  falls  down  or 

moves,  this  may  cause  personal  injury  and/or 

property damage.

•  When  unpacking  or  moving  the  unit,  be  sure  to 

handle  it  with  two  or  more  persons.  Falling  or 

dropping the unit may cause personal injury and/or 

property damage.

When the Unit is in Use 

•  Do not stand or sit on, nor hang down from the unit 

as this may cause it to fall down or drop, resulting in 

personal injury and/or property damage. 

•  Do not operate the unit for an extended period of 

time with the sound distorting. Doing so may cause 

the connected speakers to heat, resulting in a fire.

WARNING

CAUTION

Содержание SR-F09













Отзывы: