Toa IP-A1PG Скачать руководство пользователя страница 7

7

6. NOMENCLATURE AND FUNCTIONS

[Front]

1. Status indicator (green, blue, yellow, red)

Indicates the unit’s operating status.

Unit Operation

Status Indicator

System startup

Flashing green

Broadcast standby Continuously lit 

green

Broadcasting

Continuously lit blue

System mute*

Flashing red

Initialization or 

firmware updating

Continuously lit 

yellow

*  "System  mute"  represents  the  state  that

the  broadcast  audio  sent  out  from  the

transmitting  device  is  suspended  and  at

the  same  time,  IP  speakers  in  the  same

network  are  muted  by  the  signal  from

the transmitting device. "System mute" is

activated by mute terminal or control input

terminal.

2. Line/Mic input volume control

Adjusts  the  volume  level  of  the  Line/

Mic  input.  Rotate  this  volume  control

clockwise to increase the volume level and

counterclockwise to decrease it.

Set  this  volume  not  to  make  the  Line/Mic

input signal indicator (3) light up in red.

3. Line/Mic  input  signal  indicator  (green,

red)

Lights green when a signal is input to Line/

Mic input. Lights red when the input signal

level is too high.

4. Output signal indicator (green)

Lights green when the device is streaming

multicast audio or actively monitoring audio

out.

5. Control input terminals

Allows input of control signals from connected

external equipment to enable actions set in

the Event settings.

6. Line/Mic input terminal

Connects  with  a  microphone  or  sound

source device.

This  can  transmit  multicast  audio  stream

from the sound source device using control

input or Remote API (HTTP).

Adjust with the DIP switch according to the

output level of the connected device.

7. LAN port

Connect  to  a  PoE  switching  hub  using  a

LAN cable.

8. LINK/ACT indicator (green)

Flashes when data is being sent or received

over a network.

9. Mute terminal (24 V DC CUT)

By the control signal of cutting 24 V DC, this

unit is in the “System mute” state. “System

mute”  means  the  audio  transmission

from  this  unit  is  forcibly  disabled,  and  this

unit  sends  mute  control  signal  to  mute  IP

speakers in the same network segment.

When using this terminal, turn on the Mute

switch (12).

[Bottom]

[Rear]

T H C

1 2 C

1 2 3

4

5

5

6

7 8 9 10 11

12 13

14

15

The figure with a removable terminal plug detached.

Содержание IP-A1PG

















Отзывы: