TLV MC-COSR-16 Скачать руководство пользователя страница 5

Страница: 5 / 38

Specifications

Install properly and DO NOT use this product outside the recommended

operating pressure, temperature and other specification ranges.

Improper use may result in such hazards as damage to the product or

malfunctions which may lead to serious accidents. Local regulations

may restrict the use of this product to below the conditions quoted.

CAUTION

Use only under conditions in which no freeze-up will occur. Freezing

may damage the product, leading to fluid discharge, which may cause

burns or other injury.

CAUTION

Refer to the product nameplate for detailed specifications.

Primary Pressure Range

Model

Serial Number

Nominal Diameter

Maximum Operating
Temperature

Secondary Pressure
Adjustable Range

Valve No.*

* Valve No. is displayed for products with options. This item is omitted from the nameplate when there are no

options.

Actuator Specifications

Actuator Model

MC-GA2

Power Source Voltage  Free between 100 and 240 V AC (50/60 Hz)
Power Consumption  With motor running: 75 VA max.
Insulation Resistance  500 V DC, 100 M



min. between the power source

terminal and ground terminal

Power Source Withstand Voltage

Between the power source terminal and ground terminal:
1500 V AC, 1 min. or 1800 V AC, 1 second

Drive System

Positional control by DC brushless motor

Operation Input
(Valve Opening)

4 – 20 mA DC (input impedance 250



)

Emergency Action

Valve fully closed by an operation signal interruption.
When input power is cutoff: held at position just before
power cutoff

Time Rating

Continuous

Thermal Protection

Built-in overcurrent protection circuit

Time Required to Fully
Open/Close

Fully closed

→

fully open: Approx. 15 seconds

Operation

Manual Operation

Possible with the power OFF

Allowable Ambient Temperature Range 0 to 50 °C (32 to 122 °F)
Allowable Ambient Humidity

10% to 90% RH (without dew)

Allowable altitude

2000m (6600 ft) max.

Vibration Resistance

0.5 G max.

Water Resistance

Rain resistant (equivalent to IP54)

Environment

Material

Motor cover: Aluminum
Main mounting plate: FC25 (cast iron)

172-65185A-08 (MC-COSR Multi-control Valve) 20 Nov 2014

Содержание MC-COSR-16







































Результаты поиска

Содержание MC-COSR-16

Отзывы:

Похожие инструкции для MC-COSR-16

Бренды по названию

Популярные бренды

TLV MC-COSR-16, Инструкция по эксплуатации

Результаты поиска

Содержание MC-COSR-16

Отзывы:

Похожие инструкции для MC-COSR-16

Бренды по названию

Популярные бренды