TLV MC-COSR-16 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 38

background image

30

Troubleshooting

When disassembling or removing the product, wait until the internal

pressure equals atmospheric pressure and the surface of the product

has cooled to room temperature. Disassembling or removing the

product when it is hot or under pressure may lead to discharge of fluids,

causing burns, other injuries or damage.

CAUTION

When using this product, NEVER stand close to, or leave tools anywhere

near moving parts, such as the ajustment screw. Contact with moving

parts or objects becoming caught in moving parts could lead to injury or

damage or other accidents.

CAUTION

This product is shipped after stringent checks and inspection and should perform its
intended function for a long period of time without failure. However, should there be
any problem encountered in the operation of the MC-COSR, identify where the
trouble occurs and consult the troubleshooting guide below. When a problem arises,
the trouble may lie in the MC-COSR drive section, pressure reducing valve section
or the controller.

Identifying Problem Areas

1. Set the operation mode to MANUAL (MAN) on the controller connected to the

MC-COSR. This is to enable the operation signal to the drive section to be
changed to any value.

2. Set the control output on the controller to any value. Check to make sure that the

pressure adjustment screw in the drive section is stopped completely and is not
hunting (the secondary steam pressure is stabilized).

172-65185A-08 (MC-COSR Multi-control Valve) 20 Nov 2014

3. Increase the control output on the controller. Check to make

sure that, as viewed from above, the pressure adjustment
screw rotates clockwise while moving downward, and that
the secondary steam pressure increases.

Adjustment

Screw

Clockwise &

Down

4. In the same manner, decrease the control output on the

controller. Check to make sure that, as viewed from above,
the pressure adjustment screw rotates counterclockwise
while moving upward, and that the secondary steam
pressure decreases.

5. If the process in steps 2. – 4. above reveals that:

• The pressure adjustment screw is operating normally but

the secondary steam pressure does not change, then see the

Pressure

Reducing Valve Troubleshooting

section.

• The pressure adjustment screw does not rotate, then go on to the next step.

Adjustment

Screw

Counter-

clockwise

& Up

«
...
29
30
31
32
33
...
»

Содержание MC-COSR-16







































Отзывы:

Нет отзывов

Похожие инструкции для MC-COSR-16

Бренд: C&K systems Страницы: 2

Бренд: VADDIO Страницы: 2

Бренд: B&R Industries Страницы: 89

Бренд: Nabco Страницы: 35

Бренд: Parker Страницы: 32

Бренд: Rayrun Страницы: 4

AeGIS 7000 Series

Бренд: PACH & COMPANY Страницы: 2

Бренд: RadioMaster Страницы: 49

SUPERREMOTE UR19A

Бренд: X10 Страницы: 3

Бренд: Xantech Страницы: 102

Бренд: Xantech Страницы: 17

Бренд: X10 Страницы: 2

Бренд: RadioMaster Страницы: 10

Бренд: Xblue Networks Страницы: 2

Бренд: Automated Logic Страницы: 10

Бренд: Harman Страницы: 2

Бренд: Linear Technology Страницы: 6

Бренд: Nortek Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды