TLV JH7RM-P Скачать руководство пользователя страница 15

Страница: 15 / 18

172-65456MA-04 (JH7RM-P) 14 Jul 2015

Product Warranty

1. Warranty Period

One year following product delivery.

2. Warranty Coverage

TLV CO., LTD. warrants this product to the original purchaser to be free from
defective materials and workmanship. Under this warranty, the product will be
repaired or replaced at our option, without charge for parts or labor.

3. This product warranty will not apply to cosmetic defects, nor to any product

whose exterior has been damaged or defaced; nor does it apply in the following
cases:

1) Malfunctions due to improper installation, use, handling, etc., by other than

TLV CO., LTD. authorized service representatives.

2) Malfunctions due to dirt, scale, rust, etc.

3) Malfunctions due to improper disassembly and reassembly, or inadequate

inspection and maintenance by other than TLV CO., LTD. authorized service
representatives.

4) Malfunctions due to disasters or forces of nature.

5) Accidents or malfunctions due to any other cause beyond the control of

TLV CO., LTD.

4. Under no circumstances will TLV CO., LTD. be liable for consequential economic

loss damage or consequential damage to property.

* * * * * * *

For Service or Technical Assistance:

Contact your

representative or your regional

office.

Manufacturer

CO., LTD.

881 Nagasuna, Noguchi
Kakogawa, Hyogo 675-8511 JAPAN
Tel: 81-(0)79 - 427 - 1800

Содержание JH7RM-P



















Результаты поиска

Содержание JH7RM-P

Отзывы:

Похожие инструкции для JH7RM-P

Бренды по названию

Популярные бренды

TLV JH7RM-P, Инструкция по эксплуатации

Результаты поиска

Содержание JH7RM-P

Отзывы:

Похожие инструкции для JH7RM-P

Бренды по названию

Популярные бренды