TLV GP10 Скачать руководство пользователя страница 32

Страница: 32 / 41

172-65318MA-04 (GP10/GT10/GP14/GT14 PowerTrap) 23 Nov 2018

6. Removing / Reinstalling the Intake Valve and Intake Valve Seat

(Motive Medium)

The following procedure can be used to remove and replace the intake (motive medium)
valve without first removing the cover of the PowerTrap.

Part

Disassembly

Reassembly

Plug /

Plug Gasket

• Using a 38 mm (1½ in) socket

wrench, loosen the plug.

• Finish loosening by hand, and

remove the plug and plug gasket.

• Coat plug threads with anti-seize

and reinstall plug and plug gasket.

• Tighten to a torque of 160 N

⋅

(115 lbf

⋅

ft).

Intake Valve
(motive medium)
/ Screen

• Using needle-nose pliers, remove

the intake valve and screen.

• Replace the screen and valve with

new, and assemble in reverse
order of disassembly.

Intake Valve Seat
(motive medium)
/ Valve Seat
Gasket

• Using a 17 mm (

⁄

) socket

wrench with an extension bar,
loosen the valve seat.

• Using needle-nose pliers, grasp

and remove the valve seat.

• Using a needle tool, dislocate the

valve gasket, then catch and lift it
out with either the needle or
needle-nose pliers.

• Make sure you have removed the

old valve gasket. Insert and
position a new gasket.

• Coat threads of valve seat with

anti-seize.

• Using needle-nose pliers, insert

the valve seat.

• Tighten to a torque of 160 N

⋅

(115 lbf

⋅

ft).

(1 N

⋅

≈

10 kg

⋅

cm)

NOTE: It is possible to remove and

replace the intake valve
(motive medium) without
first removing the cover of
the

PowerTrap

(see

instructions above).

Intake Valve Unit

Plug

Plug Gasket

Intake Valve
(Motive Medium)

Screen

Intake Valve Seat
(Motive Medium)

Valve Seat Gasket

Содержание GP10









































Результаты поиска

Содержание GP10

Отзывы:

Похожие инструкции для GP10

Бренды по названию

Популярные бренды

TLV GP10, Инструкция по эксплуатации

Результаты поиска

Содержание GP10

Отзывы:

Похожие инструкции для GP10

Бренды по названию

Популярные бренды