TLV GP10 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 41

background image

172-65318MA-04 (GP10/GT10/GP14/GT14 PowerTrap) 23 Nov 2018

28

4. Removing / Reattaching the Snap-action and Lever Units

It is not necessary to remove the float before removing the snap-action and lever units.
When working with the snap-action unit, take care not to pinch fingers, etc.

Part

Disassembly

Reassembly

Lever
Arm

• Pull the end of the lever arm down until the

snap-action unit snaps over and the float end of
the lever arm is at its lowest position.

• See disassembly.

Bolts

• Using a 19 mm (¾in) socket wrench, loosen the

four bolts that hold the snap-action and lever units
to the cover.

• Assemble the bolts and spring

washers, then finger-tighten.

• Tighten to a torque of 60 N

⋅

m

(44 lbf

⋅

ft), following an

alternating cross-wise pattern.

Snap-Act
ion Unit /
Lever
Unit

GP10/GP14:

• Support the snap-action and lever units with one

hand while removing the loosened bolts from the
cover with the other.

• Remove the snap-action and lever units.

• Align the snap-action and lever

units, then position them by
carefully aligning the
snap-action and lever unit bolt
holes to the bolt holes in the
cover.

GT10/GT14 – To remove only the snap-action unit,
leaving the lever unit still attached to the trap unit:

a) Support the snap-action unit and lever units in

one hand while removing the four bolts.

b) Remove the snap-action unit, then carefully tip

the lever unit forward until it rests on the trap unit.

• Align the snap-action unit to

the lever unit, then position
them by carefully aligning the
snap-action and lever unit bolt
holes to the bolt holes in the
cover.

GT10/GT14 – To remove both snap-action and
lever units:

a) Remove the pin that connects the lever unit to the

trap unit (see step 7).

b) Supporting the snap-action unit and lever units in

one hand, remove the four bolts.

c) Remove the snap-action and lever units.

• Align the snap-action and lever

units, then position them
(bottom-first, in order to clear
the trap) by carefully aligning
the snap-action and lever unit
bolt holes to the bolt holes in
the cover.

(1 N

⋅

m

≈

10 kg

⋅

cm

)

NOTE: When replacing the lever unit,

follow the instructions on page
33 to adjust the gap between
the lever unit arm and pivot pin.

(GT10/GT14 only)

Snap-action Unit

Lever Unit

Spring Washer

Bolt

GP10/GP14 shown.
GT10/GT14 configuration
differs slightly.

Lever Arm

«
...
27
28
29
30
31
...
»

Содержание GP10










































Отзывы:

Нет отзывов

Похожие инструкции для GP10

Бренд: Danfoss Страницы: 12

Бренд: Jacuzzi Страницы: 8

Бренд: Campbell Страницы: 2

Бренд: Danner Страницы: 2

Бренд: Daikin Страницы: 316

Бренд: Magic-Pak Страницы: 18

FastHeat Digital 14160

Бренд: Kerbl Страницы: 32

Бренд: Pentair Jung Pumpen Страницы: 26

Бренд: TTulpe Страницы: 24

Бренд: Wilo Страницы: 16

Бренд: Fairland Страницы: 28

Бренд: Frymaster Страницы: 2

Бренд: Wacker Neuson Страницы: 208

Бренд: GORMAN-RUPP PUMPS Страницы: 45

Бренд: Greenlee Страницы: 34

PWS BEV-300 Series

Бренд: Pure Water Страницы: 35

Бренд: Graco Страницы: 14

Бренд: Heatcraft Refrigeration Products Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды