TLV GP10 Скачать руководство пользователя страница 27

Страница: 27 / 41

172-65318MA-04 (GP10/GT10/GP14/GT14 PowerTrap) 23 Nov 2018

1. Removing / Reattaching the Body from / to the Cover

Prepare a new, replacement cover gasket before beginning this step.

Part

Disassembly

Reassembly

Drain Plug

• Discharging condensate is carried out with intake

(motive medium), exhaust, inlet and outlet piping still
connected to the unit.

• Using a 300 mm (12 in) long adjustable wrench, slowly

loosen plug to release pressure and discharge fluid;
take care to avoid being burned by fluid discharge.

• Wrap threads with

3 – 3.5 turns of
sealing tape or apply
sealing compound.

• Tighten to a torque of

30 N

⋅

m (22 lbf

⋅

ft).

Cover Bolts

• Using a 30 mm (1

⁄

in) socket wrench, loosen each

bolt slowly one turn in an alternating diagonal pattern.

• Once all bolts have been loosened, verify that there is

no internal pressure before completely removing the
bolts.

• Reverse steps in

disassembly.

• Tighten to a torque of

200 N

⋅

m (150 lbf

⋅

ft).

Anchors

• Remove the bolts that hold the anchor brackets to the

body and rotate the anchor brackets on their base
bolts so that they will not interfere with removal of the
body from the cover.

• Reverse steps in

disassembly.

Body / Cover • Make sure to secure sufficient space around the body

to allow it to be pulled straight off.

• As the body weighs approximately 90 kg (200 lb), use

a block and tackle hoist to assist in its removal.

• When moving the body away from and clear of the

cover, lift the body only about 1 cm (

⁄

in), to avoid

contact with the float and other internal parts.

• In addition, to avoid contact with the float when

removing the body, lift the float and the float lever
slightly.

• Do not tilt the body more than 15° in any plane.

• Reverse steps in

disassembly.

Cover
Gasket

• The gasket will be destroyed upon disassembly,

adhering to both body and cover; using a scratch-free
scrapper, carefully scrape the gasket from both body
and cover surfaces.

• Check that all pieces

of old gasket have
been removed, then
install a new gasket.

(1 N

⋅

≈

10 kg

⋅

cm)

Cover Bolt

Cover

Cover Gasket

Body

Drain Plug

Plug for
Level Gauge

GP10/GP14 shown.
GT10/GT14 configuration
differs slightly.

Содержание GP10









































Результаты поиска

Содержание GP10

Отзывы:

Похожие инструкции для GP10

Бренды по названию

Популярные бренды

TLV GP10, Инструкция по эксплуатации

Результаты поиска

Содержание GP10

Отзывы:

Похожие инструкции для GP10

Бренды по названию

Популярные бренды