TLV A46S страница 14 Скачать руководство пользователя

Страница: 14 / 15

172-65203MA-02 (A-BD2) 21 Apr 2010

Options

When operating the blowdown valve, stand to the side well clear of the

outlet to avoid contact with internal fluids that will be discharged. Failure

to do so may result in burns or other injury.

CAUTION

Do not use excessive force when opening the blowdown valve. Such

force may break the pin equipped as a valve stopper pin, causing a

blowout from internal pressure resulting in burns or other injury.

CAUTION

With Blowdown Valve (TLV BD2)

Configuration

TLV Blowdown Valve: BD2

The BD2 Blowdown Valve, installed in the screen area of the body, uses the

trap’s internal pressure to blow any condensate, steam, dirt or scale
accumulated around the screen area out to atmosphere.

Discharge Hole

BD2 Valve

BD2 Valve Seat
(Screen Holder)

Screen Holder Gasket

Valve Stopper Pin

Screen

Содержание A46S
















Результаты поиска

Содержание A46S

Отзывы:

Похожие инструкции для A46S

Бренды по названию

Популярные бренды

TLV A46S, Инструкция по эксплуатации

Результаты поиска

Содержание A46S

Отзывы:

Похожие инструкции для A46S

Бренды по названию

Популярные бренды