Titon aura-t Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 32

background image

30

HRV ECOaura Defaults

The table below details HRV settings and defaults, which that the

aura-t

™ CANNOT

configure. During installation and commissioning they may be changed from the
default values by an alternate Titon controller. There is space available in the table
where the installer should record configuration settings.

Configurable Item

Range

Default

Configured

Min

Max

Boost Delay Timer

Kitchen

0 mins

60 mins

0 mins

Wet Room

0 mins

60 mins

0 mins

If the Boost Delay Timer is set greater than zero momentary switches will not switch the HRV into Speed 3 Boost. When using latching
switches the HRV will not Boost until the Delay time has elapsed.

Filter Change Interval

3 Months

24 Months

12 Months

Summer Bypass Enable/Disable

Enabled

Disabled

Enabled

Frost Protection Mode

Off

Reduce

Off

Frost Protection Threshold

-2°C

11.5°C

2°C

When Frost Protection is operating in Off Mode the Supply fan is switched off when the temperature measured by the sensor on the to
atmosphere side of the heat cell drops below the Frost Protection Threshold. When operating in Reduce Mode the speed of the Supply Fan
is gradually reduced when the temperature drops below the threshold. At 4°C below the threshold it is stopped.

Duct Heater Enable/Disable

Enabled

Disabled

Disabled

Duct Heater Mode

Frost

User

Frost

Duct Heater Threshold

-4°C

16°C

4°C

Duct Heater Hysteresis

1°C

10°C

1°C

When operating in Frost Mode the Duct Heater uses the sensor on the to atmosphere side of the Heat Cell and switches on 2°C above the
Frost Protection threshold. When operating in User Mode it uses the sensor on the from atmosphere side of the heat cell and the threshold
and hysteresis detailed above. In both modes the Duct Heater will be switched off if the Supply fan speed drops below 22.5% PWM.

Internal Humidity Boost

On

RH Boost Overrun

1 min

60 mins

15 mins

RH Boost Hysteresis

1%

10%

1%

When the Humidity of the air being extracted from the property reaches the threshold configured by the

aura-t

™ the fans switch to Speed

3 Boost. They remain at Speed 3 until the Humidity has dropped below the threshold minus the hysteresis and the RH Boost Overrun time
has elapsed.

«
...
28
29
30
31
32
»

Содержание aura-t

































Отзывы:

Нет отзывов

Похожие инструкции для aura-t

Бренд: Wasp Страницы: 16

TLE Scalable 150

Бренд: GE Страницы: 6

Бренд: GE Страницы: 3

Бренд: GE Страницы: 80

PACSystems* RX3i

Бренд: GE Страницы: 39

PACSystems* RX3i

Бренд: GE Страницы: 35

PACSystems* RX3i

Бренд: GE Страницы: 3

PACSystems* RX3i

Бренд: GE Страницы: 169

PACSystems RX7i

Бренд: GE Страницы: 317

Бренд: Hansen Страницы: 4

Бренд: 2gig Technologies Страницы: 4

Бренд: 2gig Technologies Страницы: 2

Бренд: G1SLE Страницы: 2

Бренд: EasyIO Страницы: 12

Бренд: RMG Страницы: 6

Бренд: National Instruments Страницы: 6

Бренд: National Instruments Страницы: 6

Бренд: IDTECK Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды