TITAN ALARM PANEL
INTRODUCTION
The TITAN Alarm Panel is part of a unique lighting / security system for home or
business use. The unit is designed to protect your property, serving as a basic
alarm system and also with the addition of a TITAN Bell Push Transmitter a door
chime unit. In addition to the bell push the TITAN alarm panel is compatible with
the TITAN wireless PIR Detector and wireless Magnetic Contact Detector. In
alarm mode when triggered by the latter two transmitters the 110 decibel siren will
sound. The Bell Push will trigger a chime alert when in chime mode.
Note: Please read this entire manual before you start to install the system.
LOADING THE BATTERIES
The unit requires four AA size batteries. To install the batteries:
1. Open the battery cover. (FIGURE 1)
2. Insert four AA batteries ensuring correct polarity.
3. Refit the battery cover.
If during use the Low Battery LED
flashes every three seconds, the batteries need to be
replaced. Average battery life for typical usage is six months, subject to alkaline batteries
being used.
CHOOSING A MOUNTING LOCATION
l
DO NOT fix the unit onto metalwork or within 1m of metalwork (i.e. radiator, water pipes etc) as this could affect the receipt
of signals from TITAN transmitters.
l
DO NOT locate the unit directly above a heat source (e.g. fire, radiator, boiler etc).
l
DO NOT expose the unit to the weather or liquids. The unit is not weather proof.
Consider the following points when choosing a mounting location. Locate the unit:
1) Within a protected area when the system is set, i.e. an intruder should not be able to reach the unit without a transmitter
detector being triggered.
2) In a position where it is not visible from external doors or windows.
3) In an easily accessible position between 1.5m and 2.0m above floor level.
The unit should be fixed using two screws 50mm apart. The screw heads should be left proud to allow the unit to be attached
using the two keyhole slots at the rear of the unit.
FIRST TIME POWER UP
The unit is capable of holding up to twelve TITAN transmitter
codes. On first time power up no codes will be stored. To
indicate this the Status LED will flash on and off every three
seconds.
The factory default 4-digit security code is set to 1234 (Note that
if the batteries are removed or allowed to run flat the unit will
default back to the factory 4-digit security code of 1234).
It is important to change the factory 4-digit security code of 1234
to your own personal code. To do this proceed as follows:
1) Key in the factory 4-digit security code 1234
2) Press key 6
3) Enter your new personal 4-digit code (using any combination of keys 0 to 9)
4) Press key 6 again
Your personal 4-digit code is now set and should be used for any further actions. (Note this process must be completed within
15 seconds. If you make a mistake or run out of time the unit will revert back to the factory 4-digit security code 1234).
CODE LEARNING
To enable the TITAN Alarm Panel to memorise compatible TITAN transmitter codes proceed as follows:
a) Key in your 4-digit security code
b) Press key
Ý
(the unit is now in learning mode and will remain so for thirty seconds, the Status and Low Battery LEDs
will flash to indicate this)
c) Once the unit is in learning mode activate the learning mode for the TITAN transmitter you wish the TITAN Alarm
Panel to learn from. Refer to the instructions for each type of transmitter in order to do this. During learning mode the
Page 1 of 2
Default Setting
(4-digit security code)
Mode Key
Mode Status
1234
1
Instant Arm
1234
2
Delayed Arm
1234
3
Chime
1234
4
Disarm
1234
6
Security Code
1234
8
Key Tone
1234
Ý
ID Code Learn Mode
1234
#
ID Code Clearance
Key Combination Quick Reference Guide
Status LED
Low Battery
LED
Siren
FIGURE 1
Key Combination Quick Reference Guide
