Tiso BASTION TWIN AUIA.097-X2 страница 3 Скачать руководство пользователя | Manualshive

Страница: 3 / 46

background image

3

INTRODUCTION

This Operation Manual (hereinafter referred to as OM) covers the servo

-

operated

turnstile (hereinafter referred to as the "turnstile"). The Operation Manual contains information
about design, specifications, installation for proper operation and maintenance of the turnstile.

This Operation Manual is prepared in compliance with the specification requirements ТУ

У 28.9

-

32421280

-

005:2018.

The turnstile shall be serviced only by the qualified staff having the relevant class of

permit to work with electrical facilities with voltage up to 1000 V and scrutinizing this Operation
Manual, obtaining safety instructions and trained for operation and maintenance of the turnstile.

Reliability and durability of the turnstile operation is provided with observation of modes

and conditions of transportation, storage, installation and operation. So, fulfillment of all
requirements specified in this document is mandatory.

Due to regular improvement of the product its design can be modified without

degradation of the product features and quality not covered by this Operation Manual.

Depending on the turnstile purpose and design features, the following pattern of reference

designation is accepted:

T3. XXX. X X. X

турникет полуростовой

Т3

1

Single

2

Double

-

TCC

Servo

-

operated

О

without antipanic device

solid body tripod

Е

with mechanical antipanic
device

(3 barrier rods)

М

with electromechanical

antipanic device

TCY

Servo

-

operated

one

-

piece elongated body

tripod (3 barrier rods)

S

Brushed stainless steel

P

Polished stainless steel

K

Painted body

TCG

Servo

-

operated

head body tripod

(3 barrier rods)

TYK

Servo

-

operated

corner body tripod

(3 barrier rods)

The tripod type turnstile reference designation is given in Table 1.

Table 1

Name

Code

Designation

CENTURION

-

М TWIN

T3.TCC.ХE.2

AUIA.095

-

10

-

X2 OM

BASTION

-

М TWIN

T3.TCY.ХE.2

AUIA.097

-

10

-

X2 OM

TWIX

-

М TWIN

T3.TYK.ХE.2

AUIA.137

-

10

-

X2 OM

Example of reference designation of the servo-operated turnstile with solid body of

brushed stainless steel when the turnstile T3.ТСC.SE.2 ТY Y

31.6-32421280-005:2018 is

ordered

«
1
2
3
4
5
...
»

Содержание BASTION TWIN AUIA.097-X2















































Отзывы:

Нет отзывов

Похожие инструкции для BASTION TWIN AUIA.097-X2

AUTOMATIC SYSTEM PPV323

Бренд: Ier Страницы: 39

Бренд: ZKTeco Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды