background image

 

17 

Altitude: Operating below 2000m 
Storage Temperature: -20

o

C ~ 60

o

C, < 80% R.H. (with battery removed)  

Temperature Coefficient: Nominal 0.15 x (specified accuracy)/ 

o

C @ (-10

o

C ~ 18

o

C or 28

o

~ 45

o

C), or otherwise specified 

Sensing: True RMS sensing 
Ingress Protection: IP40 
Pollution Degree: 2 
Safety:  Certified  per  IEC/UL/EN61010-1  Ed.  3.0,  IEC/UL/EN61010-2-030  Ed.  1.0, 
IEC/UL/EN61010-2-033  Ed.  1.0,  IEC/UL/EN61010-031  Ed.  1.1  and  the  corresponding 
CAN/CSA-C22.2 regulations to Measurement Categories:  

CAT II 1000V, CAT III 600V and CAT IV 300V AC & DC 

Transient Protection: 6.0kV (1.2/50

s surge) 

E.M.C. : Meets EN61326-1:2013 

In an RF field of 3V/m: 

Temperature function is not specified 
Ohm function:  

Total Accuracy = Specified Ac 15 digits 

Other functions: 

Total Accuracy = Specified Accuracy 

Performance above 3V/m is not specified 

Overload Protection:  

A: 11A/1000V DC/AC rms, IR 20kA, F fuse or better 
V, AutoV & L3: 1100V DC/AC rms 
mV, Ohm & others:
 1000V DC/AC rms 

Low Battery: Below approx. 2.5V 
Power Supply: 1.5V AAA Size battery X 2 
Power Consumption (typical): 
3.2mA 
APO Consumption (typical): 10

A  

APO Timing: Idle for 30 minutes 
Dimension: 161*80*50mm L*W*H (With Holster)  
Weight: Approx. 334 gm (With Holster) 
Special  Features:  AutoV  (LoZ);  3-Phase  Rotation  detection;  VFD;  BeepLit™  Continuity; 
Auto-ranging  MAX/MIN/AVG  Record;  Backlighted  LCD;  Auto-ranging  Relative  Zero  mode; 
Display Hold; EF-Detection (NCV); BeepJack™ on A terminal 
Accessories:  Test  lead  set;  Alligator  clip  set;  Batteries  installed;  User’s  manual;  Banana 
plug type-K thermocouple 
Optional Purchase Accessories: BKB32 banana plug to type-K socket plug adaptor; 
BMH-01 magnetic hanger; soft carrying pouch 

Содержание E217

























Отзывы: