TIPTEL Ergophone C Скачать руководство пользователя страница 48

Страница: 48 / 59

Appendix

Overview of codes for programming

Programming without PIN protection

Settings that need to be adjusted only in rare cases can be made via a simple procedure.

The factory pre-set is indicated by the symbol (F).

You can access the programming level by pressing the P key and the # key consecutively.

Then, enter the two-digit function code.

Code Feature

Factory pre-

set (F)

Page

01-05

Speed dialling key 1 - 5

10-19

Abbreviated dialling key 0-9

Ringing signal OFF

Ringing signal ON

Standard ringing signal operation

List of released numbers for ringing signal ON

List of restricted numbers for ringing signal ON

Indication of an incoming call by flashlight ON F

Indication of an incoming call by flashlight OFF

Room monitoring OFF

Room monitoring ON

Vitalfunction OFF

Vitalfunction ON

Programming with PIN protection

Important basic settings as well as the entry of restricted numbers and emergency num-

bers are protected by a PIN code. The factory pre-set is marked by (F).

You can access the programming level by pressing the P button and the # button after-

wards (longer than 1 second). Afterwards, enter the 4-digit PIN (in the factory pre-set, the

PIN is „0000“) and enter the 3-digit function code.

Содержание Ergophone C




























































Результаты поиска

Содержание Ergophone C

Отзывы:

Бренды по названию

Популярные бренды

TIPTEL Ergophone C, Инструкция по программированию

Результаты поиска

Содержание Ergophone C

Отзывы:

Бренды по названию

Популярные бренды