background image

TECHNISONIC INDUSTRIES LIMITED 

 

 

TDFM-9000 Installation Instructions 

TiL 11RE442 Rev. D Issue 1 

 

 
 

ESD CAUTION 

 

This unit contains static sensitive devices. Wear a grounded wrist strap and/or conductive gloves 
when handling printed circuit boards. 

 
 
 

FCC COMPLIANCE INFORMATION 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 
(1)  this  device  may  not  cause  harmful  interference  and  (2)  this  device  must  accept  any  interference 
received, including interference that may cause undesired operation. 
 

 

WARNING: 

For compliance with FCC RF Exposure Requirements the mobile transmitter 

antenna installation shall comply with the following two conditions:

 

 

1.  The transmitter antenna gain shall not exceed 3 dBi.

 

2.  The transmitter antenna is required to be located outside of a vehicle and kept at a separation distance of 70 

cm or more between the transmitter antenna of this device and persons during operation. 

 

NOTE:

  This equipment has been tested and found to comply with the limits for a Class A digital device, 

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against 
harmful  interference  when  the  equipment  is  operated  in  a  commercial  environment.  This  equipment 
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with 
the  instruction  manual,  may  cause  harmful  interference  to  radio  communications.  Operation  of  this 
equipment  in  a  residential  area  is  likely  to  cause  harmful  interference,  in  which  case  the  user  will  be 
required to correct the interference at his/her own expense. 
 
 
 

WARNING AND DISCLAIMER 

Changes  or  modifications  not  expressly  approved  by  Technisonic  Industries  could  void  the  user’s 
authority to operate the equipment. 
 
This  manual  is  designed  to  provide  information  about  the  TDFM-9000.  Every  effort  has  been  made  to 
make this manual as complete and accurate as possible. 
 
 
 

WARRANTY INFORMATION 

The  Model  TDFM-9000  Transceiver  is  under  warranty  for  one  year  from  date  of  purchase.  Failed  units 
caused by defective parts or workmanship should be returned to: 
 
Technisonic Industries Limited 
240 Traders Boulevard 
Mississauga, Ontario L4Z 1W7 
 
Tel: (905) 890-2113 
Fax: (905) 890-5338 

NOTES 

Содержание TDFM-9000









































Отзывы: