TIGIEFFE AIRO A Series Скачать руководство пользователя страница 38

Страница: 38 / 130

Use and Maintenance Manual

–

A16 J A18 J Series

Page 38

USE INSTRUCTIONS

Before using the machine read this chapter thoroughly.

WARNING!

Follow exclusively the instructions given in the next paragraphs and the safety rules described both
hereafter and in the previous paragraphs. Read the next paragraphs carefully in order to properly

understand the on/off procedures as well as all operations and their correct use.

5.1.

Platform control panel

The control panel is located on the platform. The control panel is fixed to the front guard rail and is used to:

▪

Turn the machine ON/OFF.

▪

Move the platform during ordinary working procedures.

▪

Display some parameters (alarms, dead-

man’s working, etc…).

Fig.5

Drive proportional joystick control

Proportional lever control pantograph up/down

Proportional lever control boom up/down

Proportional lever control jib up/down

Proportional lever control telescopic boom out/in

Proportional lever control turret rotation

Platform rotation switch

Platform level switch

Diesel/electric drive power selector (OPTIONAL)

Содержание AIRO A Series



































































































































Результаты поиска

Содержание AIRO A Series

Отзывы:

Похожие инструкции для AIRO A Series

Бренды по названию

Популярные бренды

TIGIEFFE AIRO A Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание AIRO A Series

Отзывы:

Похожие инструкции для AIRO A Series

Бренды по названию

Популярные бренды