Thunder Laser NOVA-24 Скачать руководство пользователя страница 5

Страница: 5 / 77

THUNDER LASER

NOVA-24

www.thunderlaser.com

DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD

[email protected]

Shatian Town, Shatian Dadao, Mintian

Tel :(86)769 826653

Dongguan City, Guangdong Province, China

Chapter1 General

1.1 General Information

Please read and follow this Operation Manual carefully, before installation and operation.
Damage to persons and/or material can result from not following individual points of the
Operation Manual!

Operation of the system is only permitted with equipment and spare parts supplied or

listed in the spare parts and consumables lists.

Auxiliary equipment must be adjusted to the base machine (any queries to dealer or

manufacturer).

The following symbols are used for easier understanding of the Operation Manual:

Caution: Warning and caution to keep in mind when operate the laser.

Caution: This component is under voltage. In these areas strictly observe

the safety instructions regarding electricity. Care is to be taken in

particular during maintenance and repair work.

Caution: In this area pay attention to the possible dangers of the laser

beam.

Caution: Indicates the potential for fire danger when operation the laser.

Do not run the laser machine when unattended

Tips: Helpful note or information on individual components of the device

that simplify the use or make it more understandable.

Содержание NOVA-24














































































Результаты поиска

Содержание NOVA-24

Отзывы:

Похожие инструкции для NOVA-24

Бренды по названию

Популярные бренды

Thunder Laser NOVA-24, Руководство пользователя

Результаты поиска

Содержание NOVA-24

Отзывы:

Похожие инструкции для NOVA-24

Бренды по названию

Популярные бренды