Thunder Laser NOVA-24 Скачать руководство пользователя страница 25

Страница: 25 / 77

THUNDER LASER

NOVA-24

www.thunderlaser.com

DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD

[email protected]

Shatian Town, Shatian Dadao, Mintian

Tel :(86)769 826653

Dongguan City, Guangdong Province, China

3.8.3

Connecting the Exhaust System

How to set up the exhaust system

Insert one side of the gray exhaust pipe into the fan inlet and the other side into the

fuselage behind the exhaust tank. Insert one side of the gray exhaust pipe into the fan

outlet and put the other side of the pipe outside where you work (If the machine is far from

the outside of the room that the gas manufactured by the machine cannot be discharged;

then you might need an dust/fume filter, it can keep the air quality of your working

environment well).

Please refer to the following pictures about how to install the exhaust pipe:

Also you can refer to the video on how to set up your Nova laser machine in our website

http://www.thunderlaser.com/how-to-use-your-laser-machine/how-to-setup-your-nova-laser-cut
ter.html

Содержание NOVA-24














































































Результаты поиска

Содержание NOVA-24

Отзывы:

Похожие инструкции для NOVA-24

Бренды по названию

Популярные бренды

Thunder Laser NOVA-24, Руководство пользователя

Результаты поиска

Содержание NOVA-24

Отзывы:

Похожие инструкции для NOVA-24

Бренды по названию

Популярные бренды