Thunder Laser NOVA-24 Скачать руководство пользователя страница 20

Страница: 20 / 77

THUNDER LASER

NOVA-24

www.thunderlaser.com

DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD

[email protected]

Shatian Town, Shatian Dadao, Mintian

Tel :(86)769 826653

Dongguan City, Guangdong Province, China

3.4 Exhaust System – Requirements

To guarantee the right ventilation during the engraving and the cutting. The device must

be equipped with a fine exhaust fan(generation of rubber dust), if you use an carbon filter

(neutralization of smells) will be better for exhaust effect. A good exhaust fan of the

outgoing air is also required when cutting plastics or engraving wood.

Connection - see section 3.7.3 connecting the Exhaust System.

Do not start the machine without an adequate exhaust system.

3.5 Air System – Requirements

To guarantee do not catch file and too much smoke during the engraving and the cutting.

The device must be connecting with the laser to make sure the laser is safe during the

work.

Содержание NOVA-24














































































Результаты поиска

Содержание NOVA-24

Отзывы:

Похожие инструкции для NOVA-24

Бренды по названию

Популярные бренды

Thunder Laser NOVA-24, Руководство пользователя

Результаты поиска

Содержание NOVA-24

Отзывы:

Похожие инструкции для NOVA-24

Бренды по названию

Популярные бренды