Thunder Laser NOVA-24 Скачать руководство пользователя страница 16

Страница: 16 / 77

THUNDER LASER

NOVA-24

www.thunderlaser.com

DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD

[email protected]

Shatian Town, Shatian Dadao, Mintian

Tel :(86)769 826653

Dongguan City, Guangdong Province, China

Chapter3 Process of Installing

3.1 Unpacking

You receive your THUNDER LASER NOVA-24 packed in a wooden box, which contains

the laser machine and additional accessories. The following steps give you an overview of

the unpacking and assembly of the laser. Please follow these steps carefully.

Keep the packing box. You will require it in case of a return.

Dispose all waste according to the applicable waste disposal law.

1. Put the wooden box on a flat and spacious room for unpacking.

2. Remove the machine box; carefully remove the foam material, which protects the

viewing window of the cover and around the machine.

3. Take out the key

，

open the door of the laser

，

Remove the accessories box which

contains all accessory parts required for the installation of the laser machine.

And check if there’s anything damaged or missed during shipping.

4. You will see an attachment table on the machine; please check whether the

accessories are all on the table.

5. Please keep the keys and the warranty certificate well (and please show us your

warranty certificate if you need tech support for the machine failure, then we will provide

you the best technical service).

6. Remove the sponge and nylon cable ties from inside the machine, and then start to

install the machine (below chapters are installation details)

Содержание NOVA-24














































































Результаты поиска

Содержание NOVA-24

Отзывы:

Похожие инструкции для NOVA-24

Бренды по названию

Популярные бренды

Thunder Laser NOVA-24, Руководство пользователя

Результаты поиска

Содержание NOVA-24

Отзывы:

Похожие инструкции для NOVA-24

Бренды по названию

Популярные бренды