Thrane&Thrane SAILOR 6110 Скачать руководство пользователя страница 26

Страница: 26 / 82

Chapter 3: Installing the system

Mounting the SAILOR 3027

3.2 Mounting the SAILOR 3027

3.2.1 Placing the SAILOR 3027 GMDSS Terminal

Place the terminal outdoors on the ship. Before mounting the terminal,
consider the following:

•

Safety distance: 1 ft. (0.3 meters).

Place the terminal so that no person can accidently get closer to the
terminal than the safety distance 1 ft. (0.3 meters).

•

Distance to exhaust fumes.

Do not place the terminal close to the funnel directly exposed to exhaust
fumes.

•

Distance to other equipment.

Keep the following distances between the terminal and other equipment:

•

Compass Safe Distance: 5 m (distance to magnetic compass)

•

HF antennas: > 5 meter

•

VHF antennas: > 4 meter

•

Other Inmarsat C terminals: > 0.5 meter

Содержание SAILOR 6110



















































































Результаты поиска

Содержание SAILOR 6110

Отзывы:

Похожие инструкции для SAILOR 6110

Бренды по названию

Популярные бренды

Thrane&Thrane SAILOR 6110, Руководство по установке

Результаты поиска

Содержание SAILOR 6110

Отзывы:

Похожие инструкции для SAILOR 6110

Бренды по названию

Популярные бренды