THORLABS LPS710/M Скачать руководство пользователя страница 16

Страница: 16 / 70

HA0378T Rev C Feb 2019

Chapter 3

3.6 Installing APT Software

DO NOT CONNECT THE CONTROLLER TO YOUR PC YET

1) Go to Services/Downloads at www.thorlabs.com and download the APT Software.
2) Run the .exe file and follow the on-screen instructions.

3.7 Electrical Connection

3.7.1 Connecting To The Supply

Note

When operating via a PC, direct user interaction with the unit is

accomplished through intuitive graphical user interface panels (GUIs),

which expose all key operating parameters and modes. The user can

select multiple panel views displaying different information about a

particular hardware unit. The multitasking architecture ensures that the

graphical control panels always remain live, showing all current

hardware activity.

Caution

Some PCs may have been configured to restrict the users ability to load

software, and on these systems the software may not install/run. If you are in

any doubt about your rights to install/run software, please consult your

system administrator before attempting to install.

If you experience any problems when installing software, contact Thorlabs on

+44 (0)1353 654440 and ask for Technical Support.

Shock Warning

The controller unit must be connected only to an earthed fused supply of

24V 2A DC.

Use only power supply cable and power supply provided with the unit,

other cables/PSUs may not be rated to the same current. The unit is

shipped with appropriate power cables for use in the UK, Europe and the

USA. When shipped to other territories the appropriate power plug must

be fitted by the user. Cable identification is as follows:

Brown Live

Blue Neutral

Green/Yellow Earth/Ground

Содержание LPS710/M







































































Результаты поиска

Содержание LPS710/M

Отзывы:

Бренды по названию

Популярные бренды

THORLABS LPS710/M, Руководство пользователя

Результаты поиска

Содержание LPS710/M

Отзывы:

Бренды по названию

Популярные бренды