THORLABS ITC1 Series Скачать руководство пользователя страница 10

Страница: 10 / 46

ITC1xx

Potentiometers

Sets the laser diode limit current

Adjusts the laser set current or power (depending on CC or CP Mode)

Sets the TEC current limit

Adjust the set temperature (transducer) or resistance (thermistor)

TEC P share

TEC I share

TEC D share

Define the TEC temperature window

For CMR adjustment. Should not be changed by the user.

Switches

Laser current controller mode
Switch to the left = constant power mode (CP)
Switch to the right = constant current mode (CC)

Laser diode polarity
Switch to the left = cathode grounded (CG)
Switch to the right = anode grounded (AG)

Temperature sensor selection
Switch to the left = thermistor
Switch to the right = transducer (AD590 etc.)

TEC I share ON/OFF
Switch towards ST2 = TEC I share ON
Switch towards ST1 = TEC I share OFF.

Jumper

JP1

Bias+

Jumper closed: bias+ connected to ST2 Pin 12

Jumper open: bias+ disconnected from ST2 Pin 12

JP2

Bias-

Jumper closed: bias- connected to ST2 Pin 9

Jumper open: bias- disconnected from ST2 Pin 9

JP4

TEC window

Jumper closed: TEC window OFF
Jumper open: TEC window ON

For compatibility with Thorlabs laser diode mounts

LEDs

LED1a

Laser ON (Upper LED)

LED1b

TEC ON (Lower LED, closest to the PCB)

LED2

Power Supply OK

LED3

TEC temperature out of window

Содержание ITC1 Series














































Результаты поиска

Содержание ITC1 Series

Отзывы:

Похожие инструкции для ITC1 Series

Бренды по названию

Популярные бренды

THORLABS ITC1 Series, Руководство по эксплуатации

Результаты поиска

Содержание ITC1 Series

Отзывы:

Похожие инструкции для ITC1 Series

Бренды по названию

Популярные бренды