8
4.2 Antenna Setup
This receiver is already adjusted for reception of Astra 19.2 satellite with the correct settings as it is
most common. Per default it is setup for DiSEqC port 1, but you can use the setting as well if you
are not connected to any switch. You only need to change these settings if you are not connected to
Astra 19.2 or you don't have this satellite connected to port 1 of your DiSEqC switch. To adjust your
antenna settings for the
Satellite
,
LNB Power
,
LNB Type
,
LNB Freq
,
DiSEqC 1.0
and
Transponder
correctly, use the
t
u
and
pq
buttons.
For the better convenience and if you have a multi dish installation, we support the
Auto DiSEqC
Scan
* function, which can be activated by pressing the
GREEN
button.
For further details and information about the settings, see chapter
7.1.1 Antenna Setup
Within the First Time Installation it is only possible to adjust settings for up to 4 satellite positions. In
order to proceed with First Time Installation, use
BLUE
Next
to go forwards.
* This new function can recognise available satellites in the persisting antenna installation. The predefined satellites are: Astra 19.2E,
Astra 23.5E, Astra 28.2E, HotBird 13.0E and Eutelsat 9.0E.
4.3 Channel list selection
In this menu you can highlight the channel list of your choice by pressing
t
u
and then choose the
appropriate option in below.
At the
Preset Channel list
option you can choose between
ORF List
,
HD Austria Senderliste
,
Family
List
and
Young Spirit
, depending on your preferences and subscription (an overview about the
different channels in each list can be found on our website www.thomsonstb.net).
In the
ORF List
you can find mainly Austrian ORF HD channels, respectively the most popular and
preferred German-language Free-To-Air TV stations in SD and HD. At the end of this list there are,
amongst others, channels from the HD Austria and Plus Austria package as well.
The
HD Austria Senderliste
mainly includes channels from the HD Austria- and Plus Austria package,
as well as the most popular ORF channels; German-language Free-To-Air TV stations in SD and
HD and international channels. This list is maintained and updated automatically by the service list
provider and cannot be edited. The channel editing can only be applied for channels which are saved
above channel number 4000 or saved in favourite list(s).
The
Family list
and
Young Spirit
serves a mixed selection of Austrian and German channels as
mentioned above, but in different sequences. These lists can be fully edited and won't be updated
automatically.
After selecting the preferred channel list, use
pq
to select the
Regional channel
option and by
pressing
t
u
or
OK
and
pq
, you decide which ORF2 HD channel should be placed on position 2 of
the selected channel list.
After your preferred channel list and the regional channels are set, press
BLUE
Next
to finish the first
installation. Your receiver will switch to the 1st channel of your selected list respectively search for the
HD Austria Senderliste
and afterwards you can enjoy watching TV with your new receiver!
Details for a channel search can be found in chapter
7.1.3 Channel Search
.
5.0 QUICK GUIDE TO USING YOUR RECEIVER
We at THOMSON understand that you can't wait to enjoy your new HD receiver. The following quick
guide will make you familiar with the basic operation of this device. We do, however, advice you to
read the full manual on our website www.thomsonstb.net to get the best performance from your
THOMSON HD receiver.
To switch your receiver on or to Standby, use the
q
button on the remote control or the button
on the left-hand side of the front panel. Please, insert your valid and activated Irdeto smartcard for
proper reception of the channel bouquet of your choice. Choose a channel with
P-/P+
respectively
use these buttons on the front panel or the
CH+/CH-
buttons. Alternatively, you can digit the channel
number with the
0~9
buttons on the remote control or press
OK
in viewing mode to display the
channel list. The volume can be adjusted with the
VOL+/VOL-
buttons. The usage of
VOL+/VOL-
and
!
is possible in all menus which present a TV picture in the background and can be used in the
videotext mode additionally. In viewing mode you can also use
t
u
.
P+/P-
enable you to scroll page wise in all list modes to choose your channel or make further
selections as conveniently as possible.