Method B – 4-digit codes Programming
Beforeyoustartprogramming,youmustfindthecodeof
thesettobecontrolled.
Refertothelistprovidedwiththeseinstructions,pageII
ofthecodes.
1. Switchonthesetyouwanttocontrol.
2. Hold down the
S
(
10
) until the
red indicator
lamp
(
1
) remains lit (the indicator light remains on
forafewsecondstogiveyouthetimetoproceedwith
the following steps.The indicator lamp flashes when
thistimeisalmostup,andthengoesoff).
3. Press the key (
3
) that corresponds to the type of
equipmentyouwanttocontrol:
TV
:televisionset,
VCR/DVD
:videocassetterecorder,DVDplayer,
DVB-T
:DVBTreceiver,
SAT
:satellite.
4. While the indicator is lit, enter the first digit of the
4-digit code proposed for the set to be controlled
(example:
0036
forThomson).Theredindicatorthen
goesoffifthecodeiscorrectorflashes,ifthecodeis
notonthelist.
5. Directtheremotecontroltowardsthesetandtryto
switchitoffbypressingthe
B
(
2
)key.
6. Shouldthesetnotswitchoff,repeatstep2.Thentype
in the next 4-digit code.Try to switch off the set by
pressing
B
(
2
) key once. Repeat this procedure by
tryingouteachofthe4-digitcodes.
Check of the programming:
In principle, your set is ready for receiving the remote control
commands.Check your remote control for proper functioning by
performing the test described on page 3.
Method C – Programming by means of
code retriever
Should none of the codes work, you still have the possibility
of retrieving the appropriate code without having to perform
any input.
1. Switchonthesetyouwanttocontrol.
2. Hold down the
S
(
10
) until the
red indicator
lamp
(
1
) remains lit (the indicator light remains on
forafewsecondstogiveyouthetimetoproceedwith
the following steps.The indicator lamp flashes when
thistimeisalmostup,andthengoesoff).
3. Pressthekey(
3
)thatcorrespondstothetypeof
equipmentyouwanttocontrol:
TV
:televisionset,
VCR/DVD
:videocassetterecorder,DVDplayer,
DVB-T
:DVBTreceiver,
SAT
:satellite.
4. Directtheremotecontroltowardsthesetandtryto
switchitoffbypressingthe
B
(
2
)key.
5. If the set you want to control switches off, press
c
(
14
)tomemorisethesubcode.
6. Should the set not switch off, press
B
(
2
) key, as
manytimesasrequired(upto200times),untiltheset
switchesoff.Waitapproximatelyonesecondbetween
keypressestogivetheredindicatorlamp(
1
)enough
timetogooffandlightupagain.Proceedingthisway
will enable you to see whether the set responds or
not.
7. Immediately upon the switching-off of the set to be
controlled,press
c
(
14
)tostorethesubcode.
Note:
If you want to assign another type of product than those
mentioned on the remote control, begin by entering a code that
corresponds to the product you want to programme (a 4-digit
code that you will find in the code booklet – see method
B
).
Example: if you want to control a satellite receiver with the
VCR/DVD
key, begin by entering a satellite code (any satellite,
for example: 0603 for a Thomson satellite receiver) then begin
the procedure.
Check of the programming:
In principle, your set is ready for receiving the remote control
commands.Check your remote control for proper functioning by
performing the test described on page 3.
Method D - Automatic code search
With this method, the remote control scrolls through the full
code list by sending an IR signal to the set to be controlled
remotely. Proceed as follows:
1. Checkthatyourequipmentison.Ifnot,switchiton
manually.
2. Hold down the
S
(
10
) until the
red indicator
lamp
(
1
) remains lit (the indicator light remains on
forafewsecondstogiveyouthetimetoproceedwith
the following steps.The indicator lamp flashes when
thistimeisalmostup,andthengoesoff).
3. Releasethe
S
(
10
)key.
4. Pressthekeycorrespondingtothetypeofequipment
(forexampleTV).
5. Pressthe
PROG+
(
15
)keyonce.Afterafewseconds
theremotecontrolbeginstolistallthecodesincluded
in the library (around 1 code per second). Press
PROG+
(
15
) a second time to reduce the speed
ofthetest(1codeevery3seconds).Assoonasthe
device changes channel you must immediately press
c
(
14
) to record the code and stop the listing. If
youhavegonepastthecode,youcangobacktothe
previous code by pressing
PROG-
(
15
) as many
times as necessary (you can go forward by pressing
B
(
2
)or
PROG+
(
15
).Assoonasthedevicereacts
again,press
c
(
14
)torecordthecode.
Note:
If you want to assign another type of product than those
mentioned on the remote control, begin by entering a code that
corresponds to the product you want to programme (a 4-digit
code that you will find in the code booklet – see method
B
).
Example: if you want to control a satellite receiver with the
VCR/DVD
key, begin by entering a satellite code (any satellite,
for example: 0603 for a Thomson satellite receiver) then begin
the procedure.
Method E – Programming for control of a COMBO
(combined TV-VCR, TV/DVD, VCR/DVD, ... set)
Depending on the COMBO group (TV/VCR, VCR/DVD, etc.) and
the make, you will be required to enter a single code for both
devices in the COMBO, or to enter two codes, one code per
device. Consult the separate list to discover this. Before you start
programming, you must find the
subcode
or
code
of the
subset to be controlled (television or video recorder).
Refer to the list supplied with this user manual (see page
subcodes
or
codes
).
GB
01_ROC4306_GB.indd 2
8/12/06 9:50:21
