THM Carbones Clavicula SE Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 40

THM Carbones Clavicula SE Скачать руководство пользователя страница 5

LOREM

T H M

C L A V I C U L A S E

5

INTRODUCTION

INTRODUCTION

Preface

This manual is an integral part of your THM component and it provides you with information
regarding the safe operation of your THM-Clavicula crank system.

Read this manual carefully prior to assembling your THM component. Always read and
observe all of the assembly and maintenance instructions in this manual, as well as those
provided in the manuals of other manufacturers whose products are used on your bicycle (e.g.
framchainwheels, pedals, etc.).

Non-observance of the information contained in this manual could result in an accident and
death or serious injury.

You will encounter the following symbols and references in this manual:



The arrow indicates the consequence of your action.

This safety message indicates a hazardous situation which,
if not avoided, could result in death or serious injury.

This message warns of a risk of material damage.

This refers to additional information or tips.

Retain this manual for other users of your THM components. Make sure that all users read,
understand and observe this manual. If you ever sell or give away your THM components, this
manual should be transferred to the new owner.

We hope you get a lot of joy from your THM components!

Your THM-Carbones Team

WARNING

NOTICE

INFO

WARNING

«
...
3
4
5
6
7
...
»

Содержание Clavicula SE









































Отзывы:

Нет отзывов