THM Carbones Clavicula SE Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 40

THM Carbones Clavicula SE Скачать руководство пользователя страница 35

LOREM

T H M

C L A V I C U L A S E

35

MAINTENANCE

Regular maintenance

The maintenance intervals required for your bicycle depend on how often and in which weather
conditions it is used.

The following maintenance measures should be conducted more frequently if the bicycle is
used in extreme conditions (rain, dirt, long distances, etc.).

When conducting regular maintenance procedures make sure your bicycle is always clean and
well protected by lubricants and cleaning agents. Ask your specialist dealer about appropriate
lubricants and cleaning agents as well as information relating to their correct application.

Risk of accident caused by a malfunctioning crank system due to loose screw
connections.

-

Check the required tightening torque of all screw connections after the
first 100 km re-tighten the connections if necessary. Repeat this check
every 2500km! Apply fresh thread lock if necessary.

Risk of accident caused by a malfunctioning crank due to wear.

-

Do not continue to use your Clavicula component if the Clavicula lettering is
abraded at one or more points (wear indicator).

Risk of accident caused by malfunctioning brakes.

-

After conducting any cleaning, maintenance or repair work make sure that
the braking rims of you wheels are free from lubricants (such as grease, oil,
silicon, Teflon, wax or other similar agents).

WARNING

«
...
33
34
35
36
37
...
»

Содержание Clavicula SE









































Отзывы:

Нет отзывов