THM Carbones Clavicula SE Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 40

THM Carbones Clavicula SE Скачать руководство пользователя страница 25

LOREM

T H M

C L A V I C U L A S E

25

INSTALL

Adjusting the bottom bracket

Accelerated bearing wear if the bottom bracket is set too rigidly due to excessive pre-
tensioning of the adjusting screw.
-Only adjust the bottom bracket if the clamping screw has been loosened! As a rule, the
required tightening torque of the adjusting screw for a correctly adjusted bottom
bracket is approximately 0.3

–

1N·m (3

–

9lbf·in).

-

Clean the threads of the adjusting
screw

(1)

-

Apply a medium-strength thread
lock (Loctite or other similar) to
the thread of the adjusting screw.

-

Screw the adjusting screw

(1)

into

the axle

–

when doing this use the

THM adjusting tool or a 6 mm allen
key.

-

Tighten  the  adjusting  screw
carefully  and  slowly  until  the
bottom  bracket  does  not  exhibit
any  play,  but  can  still  be  turned
easily by hand.

-

Adjustment of the bottom bracket
is now complete.

-

Remove the clamping screw

(2)

.

-

Apply a medium-strength thread
lock (Loctite or other similar
substance) to the thread of the
clamping screw.

-

Reassemble the clamping screw.

-

Tighten the clamping screw to

10 Nm

(89lbf·in)

.

INFO

1

2

«
...
23
24
25
26
27
...
»

Содержание Clavicula SE









































Отзывы:

Нет отзывов