Think 3D STORMBEE S20 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 102

Think 3D STORMBEE S20 Скачать руководство пользователя страница 33

STORMBEE User Manual

–

Think 3D BVBA

Version N°1.1, last modified 30/09/2018

19

4.1.2.2

With battery charging hubs (12 batteries max)

When you want to charge three or more batteries simultaneously, you need to connect the charging
hubs to the battery charger.

3.

First ensure the battery charger is powered on and has the following settings "LiPo", "Fast-
Charge", "20.0A", "Off-line".

4.

Then connect one or both charging hubs to the battery charger. Finally connect all batteries,
both their power connector and balancer connector to the respective ports of the charging
hubs.

NOTE

One battery charging hub can connect up to 6 STORMBEE batteries, but it only charges one at

a time. The first connected battery will be charged first, while the others (connected to the
same charging hub) will be charged according to their voltage level. The battery with the
highest voltage level will be charged first, then the one with the second highest and so on.

Figure 4.6 Battery charging process step 4

5.

Press the

key to enter the G630 interface.

«
...
31
32
33
34
35
...
»

Содержание STORMBEE S20







































































































Отзывы:

Нет отзывов