background image

8 .

OPERATING INSTRUCTIONS

1 . UNLATCH

A .  Raise liftgate by pushing switch to UP position, until stow pins 

are tight against nylon pads of spacer .

B .   Push spacer handle down with finger tips to disengage spacer 

latches and maintain this position through next step C .

C .   While holding spacer handle down, lower liftgate by pushing 

switch to DOWN position, until stow pins are clear of spacer 

latches . Release spacer handle .

2 .  UNFOLD

D .  Lower liftgate by pushing switch to DOWN position, and 

stop once arms contact the ground .

E .  Grasp curb side platform handle and rotate platform out 

to horizontal position .

F .   Unfold platform extension until horizontal .

3 .  RAISE OR LOWER

G . Push switch to UP position to raise liftgate . Platform levels, then raises off ground .

H .  Push switch to DOWN position to lower liftgate . Once arms contact the ground, 

continue holding switch in DOWN position, until platform nose tilts downward and 

touches ground .

4 . STORE FOR TRANSIT

I .  Raise or lower liftgate with switch, so arms are on ground 

and platform is horizontal, with platform nose off ground .

J .  Grab platform nose and fold platform extension over on 

top of main section of platform .

K .  Lift from underside of platform and fold 

entire platform upward . Grab platform 

handle on curb side to lower platform 

inward against nylon kicker roller .

L . Raise liftgate by pushing switch to UP position .

M .  Continue raising liftgate until the stow pins on both sides of the 

liftgate have powered up tight against the nylon pads on the spacer . 

MAKE SURE stow pins are engaged in latches . DO NOT lower stow 

pins on latches .

IMPROPER OPERATION OF THIS LIFTGATE MAY RESULT IN SERIOUS PERSONAL 

INJURY AND/OR DEATH.  DO NOT operate this liftgate unless you have been properly 

instructed and have read and understood the Owner’s Manual and all of its warnings, 

operating instructions and all decals .

!

WARNING

UP

DOWN

RAISE

LOWER

Содержание LRST-40

























Отзывы: