background image

 

8  

 

WARNING! 

Make sure all the DC connections are tight (torque to 9-10 
ft-lbs, 11.7-13Nm). Loose connections will overheat and could 
result in a potential hazard. 

 

2-4-4  Before proceeding further, carefully check that cable you have just connected negative 

terminal of inverter to the negative output power source. 

 

2-4-5  Connect the cable from the positive terminal of the inverter to the positive terminal of the 

power source. Make a secure connection. 

 

2-4-6  Set the power switch to the ON position; you will hear the “bi-bi-bi” sound, then the 

inerter comes into standby state.   

 

2-4-7  Set the power switch to the OFF position; the device shuts down completely. 

 

2-4-8  Please use a power meter to accurately measure the true output R.M.S. voltage of 

inverter. 

Our company uses a power meter such as IDRC CP-350 or ABM 2019 to measure our 

product. 

 

 

2-5  AC Safety Grounding 

There is an acrylic plate in front of the terminals of AC input and output. Before connecting the 

AC source and load, please remove the plate. 

 

During the AC wiring installation, AC input and output ground wires are connected to the inverter.       

The AC input ground wire must connect to the incoming ground from your AC utility source. 

The AC output ground wire should go to the grounding point for your loads (for example, a 

distribution panel of ground bus) 

 

 

CAUTION! 

Reverse polarity connection will blow a fuse in inverter and 
may permanently damage the inverter.
Damage caused by reversing polarity connection is not 
covered by our warranty. 

 

WARNING! 

You may observe a spark when you make this connection 
since current may flow to charge capacitors in the power 
inverter.  
Do not make this connection in the presence of flammable 
fumes. Explosion or fire may result.

 

YOUR CONNECTION TO SAFETY

Thiele KG 

• V
orderer W

einberg 26 • D-71522 Backnang • T

el.: +49 (0)7191 3560-0 

• Fax.: +49 (0)7191 3560-19 

[email protected] 

• www

.thiele-kg.de

Thiele KG 

• V

orderer W

einberg 26 • D-71522 Backnang • T

el.: +49 (0)7191 3560-0 

• Fax.: +49 (0)7191 3560-19 

[email protected] 

• www

.thiele-kg.de

YOUR CONNECTION TO SAFETY

klick to

www

u-s-v

YOUR CONNECTION TO SAFETY

klick to

www

ACDC-DCDC

YOUR CONNECTION TO SAFETY

klick to

www

SYSTEME

YOUR CONNECTION TO SAFETY

klick to

www

CONTACT

YOUR CONNECTION TO SAFETY

klick to

www

CALLBACK

Содержание PST700w Series
















Отзывы: