manualshive.com logo in svg

Thermopatch NL-28, Руководство пользователя, Страница: 20 / 22

Поделиться
Скачать
Thermopatch NL-28 Скачать руководство пользователя страница 20

20

For more information about our products and how to contact us, please visit thermopatch.com

BACK TO INDEX

9. End of life

 

Choose to dispose of the machine responsibly when it has reached its end of life.

Electrical machinery, accessories and packaging should be recycled as much as possible in an  

environmentally responsible manner.

•  Dismantle the machine groups: steel parts / pneumatic components / electrical components 

•  These can be separated and returned for recycling. 

 

10. Declaration of Conformity

 

  

  We,

 

 

Thermopatch B.V.

 

 

Draaibrugweg 14

  1332 

Almere

  Netherlands

 

 

herewith declare, on our own responsibility, that the machinery:

 

 

Thermopatch NL-28 v.3 heat sealing machine,

 

 

which this declaration refers to, is in accordance with the conditions of the following Directive(s):

 

 

2014/35/EG    

(emc directive)

 

 

2006/42/EG    

(machinery directive)

 

 

Netherlands, Almere, 01-05-2021

 

 

Jan Bausch,

  Director

Содержание NL-28























Отзывы:

Нет отзывов