manualshive.com logo in svg

Thermo Scientific Thermolyne NCAT F85930, Инструкция по установке и эксплуатации

Поделиться
Скачать
Thermo Scientific Thermolyne NCAT F85930 Скачать руководство пользователя страница 29

 

6  

Installation

Lift Test Procedures

Thermo Scientific

NCAT Asphalt Content Tester         

27

5. Press the balance “ENTER” key, the balance will display [BUSY], then return to the normal 

weight display.

To Escape Configuration Menu

1. Press the balance “ON/OFF” key until [ESCAPE] is displayed.

2. Press the balance “ENTER” key, the balance will return to the normal weight display.

Lift Test Procedures

The efficiency of the blower and/or exhaust system is indirectly monitored by a quick test procedure 
named the “lift test”. The procedure is detailed as follows:

1. Fully assemble tester with exhaust system attached, hearth tray is mounted on the four ceramic 

support tubes, and at room temperature with no load. This test should always be performed with 
the furnace chamber at room temperature.

2. Depress power switch to the “on” position. Depress “0” key to tare balance display.

3. Push program “start button”. Blower will turn “on”. Observe balance display reading. Display 

should read -3.2 to -8.2 grams. Detach the exhaust system and repeat the test to determine if the 
exhaust system is restricting the tester air exchange, if the initial test is out of spec or is borderline 
spec on the -3.5 grams low side.

The balance must display “0.0” before doing calibration.

This function is to reset parameters inside the balance which are not user accessible, 
the TIME, DATE, and BALANCE CALIBRATION are unaffected.

Perform the “lift test” only when the furnace is at room temperature.

Содержание Thermolyne NCAT F85930































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды