manualshive.com logo in svg

Thermo Scientific Thermolyne NCAT F85930, Инструкция по установке и эксплуатации

Поделиться
Скачать
Thermo Scientific Thermolyne NCAT F85930 Скачать руководство пользователя страница 25

 

6  

Installation

Balance Assembly

Thermo Scientific

NCAT Asphalt Content Tester         

23

Balance Assembly

Install support plate onto balance load cell with the screws provided as shown.

Do not close the control panel yet.

To install the balance:

1. Ensure that the furnace is disconnected from the power supply. Remove the four screws along the 

top of the front control panel securing the control panel to the lower case of the furnace. Move 
furnace forward about 2 inches beyond counter edge or adjust all feet up about 1/4 inch. This will 
allow the hinged control panel to open with- out obstruction.

2. Open the lower case by carefully pulling the control panel forward and downward. The control 

panel is hinged on the bottom edge to the lower furnace case. Do not allow the panel to fall 
completely open as this may excessively strain cables attached to the panel.

3. Inside the lower furnace case, observe the suspended table (balance support plate) supported by 

four aluminum rods. The balance will be supported by this table. Vacuum the table if dust, etc., 
appears on it.

4. Mount the support plate and the catch pan on the balance. Note the four pins on the catch-pan. 

These will retain the ceramic support tubes, which will project into the furnace chamber after 
mounting.

5. Place the Setra balance on the balance support table so that the gray ribbon cable is protruding 

from your left. This gray ribbon cable will be plugged into the front panel display board, into the 

Ensure that the furnace is not connected to the power supply prior to installing or 
removing the balance.

Do not allow the ceramic support tubes to contact the sides of the tube ports, as this 
will cause an unstable and inaccurate balance readout.

Содержание Thermolyne NCAT F85930































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды