Thermo Scientific Sorvall LYNX 4000 Скачать руководство пользователя страница 15

Страница: 15 / 72

Introduction and Description

Functions and Features

Thermo Scientific

Sorvall LYNX 4000 / 6000

Functions and Features

The following table gives an overview of the important functional and performance characteristics of
the Sorvall LYNX 4000 / 6000 centrifuge.

Table 3. Functions and Features

Component / Function

Description / Features

Structure / Housing

Galvanized Steel Chassis with Armoured Plating

Rotor Chamber

Stainless Steel

Drive

Induction Drive without Carbon Brushes

Touchscreen and Display

Easy-to-clean Touchscreen and Display Surface

Controls

Microprocessor-controlled

Internal Memory

Most recent Data is saved

Functions

RCF, Temperature, and Pre-temp Selection

Acceleration / Deceleration Profiles

9 Acceleration and 10 Deceleration Curves

Rotor Recognition

Automatically and instantly, when Inserting the Rotor

Imbalance Recognition

Electronic, contingent on Rotor and Speed

Centrifuge Door Lock

Automatic Centrifuge Door Closing and Locking starting from an initial
Hold Position

Rotor Lid Holder

Lefthand Side of the Centrifuge

Rotor Landing Pad

Righthand Side of the Centrifuge in Front of the Touchscreen

Order No.

entrifuge

Refrigerant Quantity

Pressure

GWP

CO2e

75006580
75006581
75006590

75006591

R-449A 1.25 kg

34 bar

1387

1.73 t

R-449A 1.25 kg

34 bar

1387

1.73 t

R-449A 1.36 kg

34 bar

1387

1.89 t

R-449A 1.36 kg

34 bar

1387

1.89 t

Refrigerants

This product complies with F-Gas regulation (EU) No

517/2014.

Contains fluorinated greenhouse gases in a hermetically sealed system.

Sorvall LYNX 4000
Sorvall LYNX 4000
Sorvall LYNX 6000
Sorvall LYNX 6000

Содержание Sorvall LYNX 4000









































































Результаты поиска

Содержание Sorvall LYNX 4000

Отзывы:

Thermo Scientific Sorvall LYNX 4000, Инструкция по эксплуатации, Страница: 15 / 72

Результаты поиска

Содержание Sorvall LYNX 4000

Отзывы: