Thermo Scientific RC 3BP Plus Скачать руководство пользователя страница 58

Страница: 58 / 70

Troubleshooting
Circuit Breakers

Thermo Scientific

Sorvall RC 3BP Plus

8-3

Circuit Breakers

The centrifuge has circuit breakers. The circuit breakers prevent the centrifuge from damages due to
residual current. In the event of a failure inform Customer Service.

Failure message

If problems occur other than those listed in this table, the authorized customer service
representative must be contacted.

Failure message

Problem with centrifuge

Possible causes and cures

NO ROTOR
DETECTED

The centrifuge cannot be operated.

The run does not start or the centrifuge
runs down without being braked.

The rotor could not be identified.

Check to see if the rotor is properly installed.

Restart the centrifuge.

If an error message appears again, inform Customer
Service.

ROTOR IMBALANCE
- BALANCE ROTOR

The centrifuge cannot be operated.

The run does not start or the centrifuge
runs down without being braked.

Imbalance detected.

Check the load placed in the rotor.

Check that the rotor cross bolts are well greased.

Restart the centrifuge.

If an error message appears again, inform Customer
Service.

CRITICAL
OVERTEMP

The centrifuge cannot be operated.

The run does not start or the centrifuge
runs down without being braked.

The run will not be interrupted.

Turn off the centrifuge.

Pull out the power supply plug.

Inform Customer Service.

SAMPLE
TEMPERATURE
OVER LIMIT

The RUN DISPLAY temperature went
above the maximum allowable
(overtemperature limit) setting.

The centrifuge cannot be operated.

The set temperature is to low for the selected speed.

The selected maximum temperature is above the
overtemperature limit.

The ambient temperature at the air inlet is >35° C.

The air inlet is blocked, the safety zone is <30 cm.

Check the aspects mentioned above. If an error message
appears again, inform Customer Service.

AIR TEMP
MEASURE ERROR

The centrifuge cannot be operated.

The cooling circuit is open.

The temperature is >45° C.

Wait for the rotor to cool down in order to prevent burn.

Turn off the centrifuge.

Pull out the power supply plug.

Inform Customer Service.

Содержание RC 3BP Plus







































































Результаты поиска

Содержание RC 3BP Plus

Отзывы:

Похожие инструкции для RC 3BP Plus

Бренды по названию

Популярные бренды

Thermo Scientific RC 3BP Plus, Инструкция по эксплуатации

Результаты поиска

Содержание RC 3BP Plus

Отзывы:

Похожие инструкции для RC 3BP Plus

Бренды по названию

Популярные бренды