Thermo Scientific Orion AquaMate 7000 Vis Скачать руководство пользователя

Страница: 82 / 148

Scanning

Viewing and Manipulating Scan Data

Orion AquaMate 7000 Vis and Orion AquaMate 8000 UV-Vis

Thermo Scientific

3. Use

Cursor

→

and

Cursor

←

to position the left cursor line to the desired wavelength

value.

The instrument calculates the 3-point net absorbance for the selected wavelengths.

4. Continue selecting the other wavelengths by pressing

Next Cursor

to activate the center

and right cursor lines.

Select the wavelengths with

Cursor

←

and

Cursor

→

Repeat until all three wavelengths have been selected.

5. Press

Enter Factor

to access the set factor box. Enter the desired factor and press

Enter

The instrument calculates the value for the 3-point net absorbance for the selected
wavelengths, multiplied by the selected factor.

Calculating the Area Under a Curve



To calculate the area under a curve

1. With your scan data displayed on the edit graph screen, press

Math

2. Press

Area

to display the Area Under the Curve measurement screen.

Содержание Orion AquaMate 7000 Vis





















































































































































Результаты поиска

Содержание Orion AquaMate 7000 Vis

Отзывы:

Похожие инструкции для Orion AquaMate 7000 Vis

Бренды по названию

Популярные бренды

Thermo Scientific Orion AquaMate 7000 Vis, Руководство пользователя

Результаты поиска

Содержание Orion AquaMate 7000 Vis

Отзывы:

Похожие инструкции для Orion AquaMate 7000 Vis

Бренды по названию

Популярные бренды