Thermo Scientific Orion AquaMate 7000 Vis Скачать руководство пользователя

Страница: 77 / 148

Scanning

Scanning a Sample

Thermo Scientific

Orion AquaMate 7000 Vis and Orion AquaMate 8000 UV-Vis

2. Place the blank in the B position.

3. Press

Collect Baseline

While the spectrophotometer is measuring the baseline, a status message appears
indicating the progress of the baseline scan. After the baseline is measured, this message
disappears.

Scanning a Sample



To scan a sample

1. Press

Run Test

If a 6-Position Cell Holder is installed, place the sample in cell position #1.

2. Press

Measure Sample

Note

To switch between tabular and graphical displays, press

Graph/Tabular

Note

If a 6-Position Cell Holder is installed, be sure to place the sample in cell

position #1. The instrument always uses cell position #1 to scan the sample.

Note

To switch between tabular and graphical displays, press

Graph/Tabular

Note

If Auto Save Data is ON, you must enter a Data File Name before you can

access Run Test or Measure Samples.

Содержание Orion AquaMate 7000 Vis





















































































































































Результаты поиска

Содержание Orion AquaMate 7000 Vis

Отзывы:

Похожие инструкции для Orion AquaMate 7000 Vis

Бренды по названию

Популярные бренды

Thermo Scientific Orion AquaMate 7000 Vis, Руководство пользователя

Результаты поиска

Содержание Orion AquaMate 7000 Vis

Отзывы:

Похожие инструкции для Orion AquaMate 7000 Vis

Бренды по названию

Популярные бренды