Thermo Scientific Orion AquaMate 7000 Vis Скачать руководство пользователя страница 56

Страница: 56 / 148

Water Analysis Application

Using a Reverse Color Method

Orion AquaMate 7000 Vis and Orion AquaMate 8000 UV-Vis

Thermo Scientific

Reverse color methods require that the instrument measure both a clear blank and a reagent
blank to properly calibrate the instrument before measuring test samples.

Using a Preprogrammed Reverse Color Method

Load the method from the library. An example of a reverse color method screen is shown
below.

To run the method, follow the sequence of steps below:

1. Press the

Run Test

function key. The following screen appears:

2. Place a cuvette, tube or vial containing a clear, colorless blank solution (such as distilled

water) in the measurement position and press the

Measure Blank

function key.

The

Measure Rgnt Blank

option will appear.

Содержание Orion AquaMate 7000 Vis





















































































































































Результаты поиска

Содержание Orion AquaMate 7000 Vis

Отзывы:

Thermo Scientific Orion AquaMate 7000 Vis, Руководство пользователя, Страница: 56 / 148

Результаты поиска

Содержание Orion AquaMate 7000 Vis

Отзывы: