Thermo Scientific Orion AquaMate 7000 Vis Скачать руководство пользователя | Manualshive

Страница: 52 / 148

background image

10

Water Analysis Application

Using the One Point Adjustment Calibration Feature

42

Orion AquaMate 7000 Vis and Orion AquaMate 8000 UV-Vis

Thermo Scientific

The AquaMate can implement factors or curves up to third order polynomials. As shown in
the screen, the format for entering the equation is:

Result = A + Bx + Cx

2

+ Dx

3

where “x” is the absorbance at the programmed wavelength.

For methods with a simple multiplicative factor, enter this factor as value B. e.g. If the factor
given with the kit is 12.68, set B=12.68, and your equation will be

Result = 12.68 * Abs

λ

where ABS

λ

is the measured absorbance at the wavelength specified in the first parameters

screen.

A large majority of commercial water kits use factor sets that require only B, or only A and B.
A limited number may require factors C and D.

Using the One Point Adjustment Calibration Feature

Use the one point adjustment feature prior to running a preprogrammed test method to
ensure accurate measurements. This procedure is recommended each time a new batch of
reagents are used to account for variations in batch-to-batch reagent composition and other
factors that affect the accuracy of a method with a fixed calibration curve.

When the one point adjustment feature is off, no adjustment is applied when running the test
and test results are calculated exactly according to the preprogrammed equation.

1. Load the test method in the Water Analysis test menu.

2. If the 1 pt Adjust parameter is set to Off, press the

keys to highlight 1pt Adjust and

press Enter to set the parameter to On.

Note

You can choose a result unit from a list of pre-programmed options or customize

your own unit. Simply select Result Units and press enter. The list will be displayed. For
more information, see

“Concentration Units”

«
...
50
51
52
53
54
...
»

Содержание Orion AquaMate 7000 Vis





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Orion AquaMate 7000 Vis

Бренд: AccuMASTER Страницы: 2

Бренд: Yamaha Страницы: 3

Бренд: Valor Страницы: 13

Бренд: Campbell Страницы: 31

Бренд: Campbell Страницы: 362

Бренд: Campbell Страницы: 60

Бренд: Campbell Страницы: 116

Бренд: Campbell Страницы: 30

Бренд: Campbell Страницы: 55

Бренд: Cannon Страницы: 64

Бренд: Cannon Страницы: 73

Бренд: M-system Страницы: 16

Бренд: M-system Страницы: 25

Бренд: GE Страницы: 35

Бренд: Yamaha Страницы: 24

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 28

Бренд: Jula Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды