Thermo Scientific Orion AquaMate 7000 Vis Скачать руководство пользователя | Manualshive

Страница: 35 / 148

background image

Thermo Scientific

Orion AquaMate 7000 Vis and Orion AquaMate 8000 UV-Vis

25

6

Managing Stored Tests

The instrument uses test method files containing the values for all parameters needed to run a
test, including those for cell changer alignment and installed accessories. After setting the
parameters, you can assign a unique test name and save the test. You can then restore the test
and run it without having to set the parameters again.

When you power-down the instrument, the current test is maintained by battery backup.
When you turn the instrument on again, the cell holder alignment and values for all
parameters are the same as when the instrument was last used. If you load a saved test, the
values for all parameters stored with it replace the current values of the test parameters.

Software Password

This password lets you “lock” test setups (test parameters) so they may not be overwritten or
deleted. The password also lets you remove the security so you may edit the test parameters.
See the Lock/Unlock section for more information on locking a test.

Password: 4363797

Naming a Test

When saving a test, specify its file name using up to eight alphanumeric characters.



To name a test

1. After setting the test parameters, highlight

Test Name

and press

Enter

.

Note

This password cannot be changed.

Note

Tests stored on a USB memory device cannot be locked or unlocked.

«
...
33
34
35
36
37
...
»

Содержание Orion AquaMate 7000 Vis





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Orion AquaMate 7000 Vis

Бренд: Halcyon Страницы: 36

Бренд: Landis+Gyr Страницы: 26

Бренд: Landis+Gyr Страницы: 3

Бренд: Omano Страницы: 14

Бренд: Parkside Страницы: 114

Бренд: X-Rite Страницы: 45

Бренд: X-Rite Страницы: 22

Бренд: Yamaha Страницы: 17

Бренд: Yamaha Страницы: 23

Бренд: Yamaha Страницы: 16

Бренд: Yamaha Страницы: 28

Бренд: Yamaha Страницы: 19

Бренд: Yamaha Страницы: 57

Clavinova CVP-204

Бренд: Yamaha Страницы: 56

disklavier Mark III Series

Бренд: Yamaha Страницы: 50

Бренд: Yamaha Страницы: 23

Бренд: Oldham Страницы: 96

Бренд: Bontempi Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды