Thermo Scientific Orion AquaMate 7000 Vis Скачать руководство пользователя | Manualshive

Страница: 27 / 148

background image

3

Accessories

External Printers

Thermo Scientific

Orion AquaMate 7000 Vis and Orion AquaMate 8000 UV-Vis

17

Removing the 6-Position Cell Holder and the Single Cell Holder



To remove the 6-Position Cell Holder and the Single Cell Holder

1. Open the sample compartment door and let it rest on its hinge.

2. With one hand, loosen the captive thumbscrew.

3. With your other hand, pull straight up on the cell holder and lift it out of the sample

compartment

4. Close the sample compartment door.

Installing Accessory Cell Holders

Make sure that you have the correct cell holder baseplate installed.

See

“Cell Holder Configurations”

for the different cell holder accessories that can

be created for your instrument.

Each of the Cell Holders needs to be installed on either a single-cell baseplate or a multi-cell
baseplate by removing the cell holder(s) secured to the baseplate. Each cell holder has a captive
screw in the bottom of the holder that secures the holder to the baseplate. Use a flat blade
screwdriver to loosen the captive screw from the baseplate and lift the cell holder from the
baseplate. Then insert the new cell holder into the appropriate position and secure it to the
baseplate by tightening the captive screw.

See

“Installing the 6-Position Cell Holder and the Single Cell Holder”

instructions on installing the complete accessory assembly in your instrument.

External Printers

Your spectrophotometer is able to print to external desktop printers supporting HP PCL 5.0
format and later.

Note

If the cell holder is not aligned correctly, you will not be able to tighten the

thumbscrews.

Note

To use 100 mm long pathlength cells, you must install the Single Cell Holder

baseplate.

Note

Remove the baseplate from the instrument before removing or installing cell

holders.

Note

PCL format does not support HP “Windows” printers.

«
...
25
26
27
28
29
...
»

Содержание Orion AquaMate 7000 Vis





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Orion AquaMate 7000 Vis

Бренд: Keithley Страницы: 148

Бренд: Landis+Gyr Страницы: 54

Бренд: Kane Страницы: 16

Бренд: Bacharach Страницы: 48

Бренд: Bacharach Страницы: 24

Бренд: Macnaught Страницы: 14

Бренд: J.P. Instruments Страницы: 9

Бренд: J.ASSY Страницы: 13

Бренд: QUNDIS Страницы: 20

Бренд: R&S Страницы: 2

Professional Plus

Бренд: YSI Страницы: 28

Wind Monitor Series

Бренд: Campbell Страницы: 38

Бренд: Favero Electronics Страницы: 12

Бренд: DAKOTA ULTRASONICS Страницы: 38

Бренд: Ansul Страницы: 24

Бренд: ENDA Страницы: 2

Бренд: Heinrichs Страницы: 31

CoolPoint CP12-V8

Бренд: UFM Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды