Thermo Scientific Orion AquaMate 7000 Vis Скачать руководство пользователя

Страница: 18 / 148

Setting Up the Instrument

Entering Parameter Values

Orion AquaMate 7000 Vis and Orion AquaMate 8000 UV-Vis

Thermo Scientific

Alternatively, you can press

Enter

to display the Entry window with the value range and then

type the complete entry and press

Enter

Menu Selection

With the parameter (Units, or Sample Positioner) highlighted, press

Enter

to display the

selection list. Highlight the appropriate item and press

Enter

On/Off Toggle

With the parameter (e.g., AutoPrint) highlighted, press

Enter

to toggle to the opposite value.

Alphanumeric Entry

With the parameter (e.g., Test Name) highlighted, press

Enter

. The Name Entry screen

appears. Highlight the desired character and press

Add Character

. When you are finished,

press

Accept Name

Содержание Orion AquaMate 7000 Vis





















































































































































Результаты поиска

Содержание Orion AquaMate 7000 Vis

Отзывы:

Похожие инструкции для Orion AquaMate 7000 Vis

Бренды по названию

Популярные бренды

Thermo Scientific Orion AquaMate 7000 Vis, Руководство пользователя

Результаты поиска

Содержание Orion AquaMate 7000 Vis

Отзывы:

Похожие инструкции для Orion AquaMate 7000 Vis

Бренды по названию

Популярные бренды